Results 101 to 110 of about 719,745 (217)

A Study of Injection Moulding with Bismuth Alloy

, 2013
There is a demand to produce parts in small quantities, using cost effective injection moulding processes. The emerging economic case suggests there will be advantages in producing injection moulding tools for short duration low volume production runs ...
Unver, Ertu, Durgun, Ismail, Jagger, Brian, Kus, Abdil, University of Uludag, University of Huddersfield, Tofas   +6 more
core  

Construction and Evaluation of the Support System for the Dispensation of Injections-An Injection Expenditure System and an Injection Audit Auxiliary System-.

Iryo Yakugaku (Japanese Journal of Pharmaceutical Health Care and Sciences), 2003
Suzuki, Masahiko, Arai, Chiharu, Teduka, Haruki, Nakazawa, Mishina, Tanaka, Mutsuko, Hanawa, Takehisa, Oguchi, Toshio, Nakajima, Shin'ichiro, Kawano, Kenji   +8 more
openaire   +3 more sources

Large Section Ceramic Injection Moulding

, 2000
PhDCeramic injection moulding is already established as a production technique for complex shaped ceramic components. However the process is limited to thin section mouldings generally not exceeding a wall thickness of 10 mm.
Krug, S., Krug, Steffen
core  

Computed tomography and magnetic resonance imaging contrast media injectors: technical feature review – what is really needed?

Medical Devices: Evidence and Research, 2016
Michael Friebe Institute of Medical Engineering, Otto-von-Guericke-University, Magdeburg, Germany Abstract: There has been little technical innovation over the last few years for contrast media (CM) injectors that are used for diagnostic imaging ...
Friebe M
doaj  

Variotherm assisted precision injection molding of plastic optical lenses based on improved cooling stage control model

Scientific Reports
Precision injection-molded plastic optical lenses are extensively utilized in imaging optical systems. The residual stress and surface deformation produced during the injection molding of plastic optical lenses will immediately result in impairments in ...
Yuwang Hu, Changxi Xue
doaj   +1 more source

Digital Twin Modeling for Smart Injection Molding

Journal of Manufacturing and Materials Processing
In traditional injection molding, each level of the process has its own monitoring and improvement initiatives. But in the upcoming industrial revolution, it is important to establish connections and communication among all stages, as changes in one ...
Sara Nasiri, Mohammad Reza Khosravani, Tamara Reinicke, Jivka Ovtcharova   +3 more
doaj   +1 more source

Additive Injection and Flow Ratio Control Systems

Measurement + Control, 1977
J. J. Jiskoot
doaj   +1 more source

Multi-period superstructure optimization for CCS source-sink matching in South Sumatra industrial clusters

Carbon Neutrality
Minimizing supply chain costs is a critical challenge for the successful deployment of full-chain CO₂ capture and storage (CCS) systems, particularly in industrial clusters with diverse source and sink characteristics.
Osaliana Budiarto, Widodo Wahyu Purwanto, Alin Halimatussadiah, Dara Ayuda Maharsi   +3 more
doaj   +1 more source

Research on Intelligent Diagnosis and Decision-Making Method for Oilfield Water Injection System Faults

IEEE Access
Water injection is a commonly used development method in oilfields. Water injection systems are large and complex, with horizontally and vertically interconnected pipeline networks often buried underground.
Ruijie Zhang, Wenting Yang, Jie Li, Shengliang Gao, Yan Wang, Sheng Gao   +5 more
doaj   +1 more source

Frequency and phase modulation performance of an injection-locked CW magnetron. [PDF]

, 2006
It is demonstrated that the output of a 2.45-GHz magnetron operated as a current-controlled oscillator through its pushing characteristic can lock to injection signals in times of the order of 100-500 ns depending on injection power, magnetron heater ...
Carter, Richard G., Tahir, I., Dexter, A.   +2 more
core