Results 11 to 20 of about 73 (73)

Control laws of an aviation gas turbine engine with a turbofan additional unit

open access: yesАвіаційно-космічна техніка та технологія, 2023
The main aspects of the general task of integrating an aviation engine (AE) with a turbofan additional unit (TAU) of a multi-mode aircraft are the selection of the scheme and design parameters of the AE with the TAU (including parameters of the work ...
Serhii Tovkach
doaj   +1 more source

РОЗРОБКА МЕТОДУ КЛАСИФІКАЦІЇ РЕЖИМІВ РОБОТИ АВІАЦІЙНОГО ДВИГУНА ТВ3-117 НА ОСНОВІ НЕЙРОМЕРЕЖЕВИХ ТЕХНОЛОГІЙ

open access: yesСучасний стан наукових досліджень та технологій в промисловості, 2018
Предметом дослідження в статті є режими роботи авіаційного двигуна ТВ3-117 та методи їх розпізнавання. Мета роботи – розробка методів класифікації режимів роботи авіаційного двигуна ТВ3-117 на основі нейромережевих технологій у режимі реального часу.
Юрій Миколайович Шмельов   +4 more
doaj   +1 more source

РОЗРОБКА ІНФОРМАЦІЙНОЇ ТА ДИНАМІЧНОЇ МОДЕЛЕЙ КОНТРОЛЮ І ДІАГНОСТИКИ ТЕХНІЧНОГО СТАНУ АВІАЦІЙНОГО ДВИГУНА ТВ3-117

open access: yesСучасний стан наукових досліджень та технологій в промисловості, 2019
Предметом дослідження в статті є авіаційний двигун ТВ3-117 та методи контролю і діагностики його технічного стану. Мета роботи – розробка інформаційної та динамічної моделей контролю і діагностики технічного стану авіаційного двигуна ТВ3-117 задля ...
Serhii Vladov   +5 more
doaj   +1 more source

APPLICATION OF NEURAL NETWORKS IN PROBLEM OF PREDICTING THE TECHNICAL CONDITION OF AVIATION ENGINE TV3-117 IN FLIGHT MODES

open access: yesАвіаційно-космічна техніка та технологія, 2018
The subject matter of the article are the methods and models for the identification of the technical state of the aircraft engine TV3-117. The goal is to develop an on-board system for identification of the technical state of the aircraft engine TV3-117,
Юрий Николаевич Шмелев   +2 more
doaj   +1 more source

APPROACH OF FUZZY CLUSTERING IN DISTRIBUTED INFORMATION SYSTEMS OF AVIATION ENGINES

open access: yesАвіаційно-космічна техніка та технологія, 2020
The article is devoted to the development of systematic approaches for the construction of a distributed information system (DIS) of aviation gas turbine engines (GTE).
Сергій Сергійович Товкач
doaj   +1 more source

DESIGN-TECHNOLOGICAL PREPARATION OF PRODUCTION DEFLECTORS USING PULSE TECHNOLOGIES

open access: yesАвіаційно-космічна техніка та технологія, 2019
The development of explosion punching processes is a rather complicated task for preparing the production of aircraft engines. The relatively large complexity and duration of production preparation, as well as the relatively high cost of the dies ...
Антон Виталиевич Онопченко
doaj   +1 more source

CURRENT STATE OF THE PROBLEM OF THE DEVELOPMENT OF ACOUSTIC LINERS FOR GAS-TURBINE ENGINES

open access: yesАвіаційно-космічна техніка та технологія, 2020
A review of current international aviation noise requirements is provided. It is shown that international requirements for aircraft noise levels are constantly increasing.
Євген Олександрович Римаренко
doaj   +1 more source

Методика експериментального дослідження термоциклічної довговічності робочих лопаток турбін ТРДДФ військового призначення

open access: yesMilitary science
Актуальність цієї статті обумовлена тим, що вкрай важливо підтримувати технічний стан парку військових авіаційних двигунів для забезпечення високого рівня надійності та безпеки польотів.
Євгеній Лайське
doaj   +1 more source

Adaptive kinematic structures for construction of an aviation gas turbine engine

open access: yesАвіаційно-космічна техніка та технологія
Depending on the operating conditions of a part or assembly of an aircraft gas turbine engine (GTE); various calculation schemes are used to calculate the stress-strain state, which differ in the finite element approximation method, material models, and ...
Serhii Tovkach
doaj   +1 more source

The influence of dynamic factors on the characteristics of the aviation engine in operating modes

open access: yesАвіаційно-космічна техніка та технологія
In the range of different flow modes for selecting the dimensions of the flow part, the rotor rotation frequency, and the design of compressors and turbines, the highest tension values for the strength were considered.
Serhii Tovkach
doaj   +1 more source

Home - About - Disclaimer - Privacy