Results 21 to 30 of about 3,428 (153)
Rare Metals, Volume 45, Issue 4, April 2026.ABSTRACT The thermal expansion mismatch between sapphire and Ti‐6Al‐4V (TC4) alloy has traditionally limited the shear strength of ceramic‐metal joints to ≤ 170 MPa. In this study, active brazing with Ag‐35.25Cu‐1.75Ti (wt%) leads to the formation of a dual‐function microstructure, wherein uniformly dispersed submicron Ti3(Cu,Al)3O particles embedded ...
Hairui Liu +13 more
wiley +1 more source
Assessment of wind-induced fatigue crack initiation life at guyed mast earplate joints considering welding residual stresses [PDF]
, 2010 A new method for assessing the degree of the cumulative fatigue crack initiation damage of the welds of earplate joints of a guyed mast,which connect the mast with the cable,is proposed.Based on the multi-scale wind-induced stress analysis of the ...
Pi, Y, Qu, W, Wang, W
core
Rare Metals, Volume 45, Issue 2, February 2026.ABSTRACT TiFe‐based hydrogen storage alloys have garnered significant attention because of their cost‐effectiveness, high hydrogen capacity, and favorable hydrogen absorption/desorption characteristics. However, practical application was limited by activation challenges and sensitivity to environmental poisoning.
Yuehai Li +8 more
wiley +1 more source
Research on residual stress measurement and vibration stress relief of sheet metal [PDF]
, 2017 小孔法的塑性效应会给高残余应力测量带来误差，为了解决这个问题，论文中对ASTME837-13a标准中的校准系数的塑性修正进行了研究。同时，组建了用于金属薄板件振动时效的电磁激振系统，研究了振动时效消除金属薄板件的残余应力。论文的研究内容围绕以下几个方面展开。 首先，研究了小孔法测量铝合金构件高残余应力的塑性效应修正方法。基于形状改变比能密度理论，对ASTME837-13a标准中的校准系数进行塑性修正；结合双线性弹塑性理论，采用ANSYS软件进行有限元仿真标定；使用电子万能试验机进行拉伸加载实验验证 ...
林俊辉
core
Integrative Conservation, Volume 4, Issue 3, Page 345-353, September 2025.Restoration of monoculture in protected and marginal areas can be organized into two phases (1) identification and prioritization of restoration sites based on remote sensing or field survey then assessing degradation level, and (2) implementation of appropriate restoration interventions.
Liang Song +9 more
wiley +1 more source
Jianzhu Gangjiegou Jinzhan, 2023 对接焊缝为钢结构典型的焊缝形式，其位置处的裂纹和气孔型缺陷准确检测对于维护钢结构有着重要的意义，使用磁记忆检测技术对焊缝裂纹和气孔型缺陷进行定位时，传统的零点极值理论会由于焊接残余应力的影响，难以区分残余应力和焊接裂纹和气孔型缺陷所产生的磁信号，使其在实际检测中造成缺陷定位的误判和漏判，因此，从焊接裂纹和气孔型缺陷和残余应力所在区域磁信号产生机理的不同入手，开展考虑残余应力影响下的焊接裂纹和气孔型缺陷定位检测研究。首先对焊接残余应力与裂纹和气孔型缺陷产生磁信号的机理进行分析 ...
陈悦, 潘学豪, 邓淋方
doaj
RESIDUAL STRESS IN HIGH TEMPERATURE MEMS SHEAR STRESS SENSOR [PDF]
, 2010 采用理论分析与数值模拟相结合的方法, 研究了残余应力对静电反馈式MEMS高温剪应力传感器的结构设计的影响.研究表明:在电极宽度和间距不变的情况下, 增加电极数和减小电极长度可有效地减小由静电力引起的应力和变形 ...
宋宏伟, 纪科星, 范学军
core
Evaluation of residual stress and its influence on fracture performance of Q690 thick plate butt welded joint [PDF]
ObjectiveThis study aims to investigate the complex welding residual stress of high-strength steel thick plate with multi-pass welding, and examines the influence of such stress on the fracture behavior of welded joints.
Hongquan ZHAO +6 more
core +1 more source
Preparation of the capillary copper/titanium composite pipe by floating-plug drawing processing and its microstructure and properties [PDF]
, 2017 A copper/titanium bimetallic composite pipe with high interfacial bonding quality was manufactured by the high-temperature rotary swaging forming, and then was processed by the floating-plug drawing process. The forming ability of drawing process and the
FU Hua-dong +4 more
core +1 more source
Direct growth of hexagonal BN films on various substrates and induction of ZnO nanorod array for piezoelectric nanogenerators [PDF]
, 2016 近年来，随着二维材料受到广泛的关注，六角氮化硼(h-BN)由于其类石墨烯的层状晶体结构，且拥有独特的特性，如宽禁带(6.0eV)、高的热稳定性(>800ºC)、强机械强度等，成为新型材料研究的热点。在短波长光电器件、高功率和高频率电子器件的开发和需求日益提升的过程中，h-BN薄膜材料研究中也面对了几个关键性、挑战性的难题：其一，大规模生产的新型光电子器件对所需的二维材料有了更高的要求，强烈需要一个大尺寸（晶圆尺寸以上）的薄膜合成，特别是在大小有限的反应腔体中合成大尺寸的h-BN薄膜；其二 ...
ABDUL MAJID
core