Creep Characteristics of Engineering Materials [PDF]
, 2019 The assessment of suitability for further service of the basic material and circumferential welded joints of primary steam pipelines made of 14MoV6-3 steel was made based on the determined characteristics of their mechanical properties and structure. The
Dobrzański, Janusz, Zieliński, Adam
core +2 more sources
Structural analysis and optimization of ash hopper design [PDF]
, 2021 The purpose of this thesis is to research and develop the design and dimensioning of boiler ash hoppers by analyzing existing hoppers and applying relevant steel structure standards.
Punkkinen, Lassi
core
A comparative study on microstructure and properties of traditional laser cladding and high-speed laser cladding of Ni45 alloy coatings [PDF]
, 2021 High-speed laser cladding technology can significantly improve the efficiency of coating preparation and effectively widen the application range of laser cladding. In this study, the Ni45 powders were deposited on steel substrate by traditional low speed
Chen, Zhaohui +4 more
core +1 more source
Technological aspects of the robotic TOPTIG surfacing of boiler steel tubes using alloy inconel 625 [PDF]
, 2017 The research aimed to develop technological parameters of the TOPTIG method-based surfacing (using alloy Inconel 625) of boiler tubes (O 45x5) made of steel 13CrMo4-5 ensuring the obtainment of the iron content on the overlay weld surface below 5%.
Grobosz, W. +4 more
core +2 more sources
Negligible creep temperature curves for EN-13445: JRC Contribution to CEN/TC 54/WG 59: Report replaces WG59 report N0024 [PDF]
, 2017 The simplified methodology proposed by JRC (in CEN TC 54 WG CREEP) for defining negligible creep temperature curves (TNEC) has here been applied to define the negligible creep (TNEC) curves and the no-creep temperature (TNC) for a service life of 200 000
HOLMSTROM BJORN
core +1 more source
Verification of heat treatment on properties of progresive heat resisting steels [PDF]
, 2009 Předmětem diplomové práce je zkouška postupu svařování žáropevné oceli T24 metodou TIG. V praxi se jedná o spojování membránových stěn při stavbě parních elektrárenských kotlů.
Volf, Ondřej
core
Journal of the American Ceramic Society, Volume 108, Issue 12, December 2025.In this study, silazanes are used as matrix material for the fabrication of lamellar corrosion protection base coats. The silazane matrix leads to a temperature stability up to 400°C of the zinc, magnesium, and aluminum‐filled coatings. At higher temperatures the coatings suffer from oxidation of the fillers resulting in reduced corrosion protection ...
Jan‐Felix Wendel +3 more
wiley +1 more source
Weldability Evaluation of Steels for Power Equipments Working with Supercritical Steam Parameters [PDF]
, 2012 Import 03/08/2012Cílem této bakalářské práce je zhodnotit svařitelnost ocelí používaných v energetice, s důrazem na moderní materiály navrhované v současné energetice (vysokoteplotní a vysokotlaké).
Vojtas, Adam
core
Einsatz des warmfesten Stahles 7CrMoVTiB10-10 (T24) als Rohrwerkstoff im 600-Grad-Kraftwerk - Besondere Qualitätssicherungsmaßnahmen zur Vermeidung der Bildung von Spannungsrissen [PDF]
, 2016 Für die Herstellung von Dampferzeugeranlagen wurden in der Vergangenheit Stähle wie der 13CrMo4-5 (T12), 16Mo3 und St35.8 III eingesetzt. In den Jahren nach 1990 wurde alternativ der Membranwerkstoff 7CrMoVTiB10-10 (ASTM-Bezeichnung T24) vorrangig in ...
Metzger, Klaus
core +1 more source
UV curing of polysilazane‐based coatings with metallic fillers for corrosion protection applications
International Journal of Applied Ceramic Technology, Volume 22, Issue 6, November/December 2025.In this study, the feasibility of UV curing a highly filled silazane‐based coating with metallic fillers is investigated. Despite the high amount of UV reflecting fillers the entire coating is cured via thiol‐ene “click” reactions. The resulting properties are comparable to those of thermally cured coatings.
Jan‐Felix Wendel +4 more
wiley +1 more source