Results 11 to 20 of about 108,174,663 (284)
Biocompatibility of 17-4 PH stainless steel foam for implant applications
Bio-Medical Materials and Engineering, 2011 In this study, biocompatibility of 17-4 PH stainless steel foam for biomedical implant applications was investigated. 17-4 PH stainless steel foams having porosities in the range of 40–82% with an average pore size of around 600 μm were produced by space holder-sintering technique.
Mutlu, Ilven, Oktay, Enver
openaire +4 more sources
Materials Research Express, 2020 Diffusion bonding of titanium (Ti) to 17-4 PH high strength stainless steel is challenging owing to the formation of brittle Ti-Fe intermetallic compounds (IMCs) at joint interface.
Bo Feng +4 more
doaj +2 more sources
Compaction behaviours of 17-4 PH, 316L, and 1.4551 stainless-steel powders during cold pressing
Results in EngineeringDespite numerous recent technological developments, conventional powder metallurgy (CPM) remains the most commonly applied technique for fabricating stainless-steel products.
Mohammed Qasim Kareem +3 more
doaj +2 more sources
Physical and mechanical properties of cast 17-4 PH stainless steel [PDF]
, 1981 The physical and mechanical properties of an overaged 17-4 PH stainless steel casting have been examined. The tensile and compressive properties of cast 17-4 PH are only influenced to a slight degree by changing test temperature and strain rate. However, both the Charpy impact energy and dynamic fracture toughness exhibit a tough-to-brittle transition ...
Rack, H. J.
openaire +4 more sources
Additively manufactured 17–4 PH stainless steels for fracture management devices
Virtual and Physical PrototypingStainless steel 316L (SS316L) is widely used in fracture management devices. However, SS316L does not offer any bacterial infection resistance and can cause metal-ion sensitivity due to Ni-ions’ presence.
Aruntapan Dash +2 more
doaj +4 more sources
Two-Phase Master Sintering Curve for 17-4 PH Stainless Steel
Metallurgical and Materials Transactions A, 2016 The sintering behavior of 17-4 PH stainless steel has been efficiently characterized by a two-phase master sintering curve model (MSC). The activation energy for the sintering of gas-atomized and water-atomized 17-4 PH powders is derived using the mean residual method, and the relative density of both powders is well predicted by the two-phase MSC ...
Jung, Im Doo +5 more
openaire +3 more sources
Characterization of Microstructural and Mechanical Properties of 17-4 PH Stainless Steel by Cold Rolled and Machining vs. DMLS Additive Manufacturing [PDF]
Journal of Manufacturing and Materials ProcessingThe 17-4 PH stainless steel is widely used in the aerospace, petrochemical, chemical, food, and general metallurgical industries. The present study was conducted to analyze the mechanical properties of two types of 17-4 PH stainless steel—commercial cold-
Pablo Moreno-Garibaldi +8 more
doaj +2 more sources
Production and aging of highly porous 17-4 PH stainless steel
Journal of Porous Materials, 2011 This study describes production of highly porous 17-4 PH stainless steel for biomedical implant applications by space holder-sintering technique. 17-4 PH stainless steel powders were mixed with space holder and then compacted. For designing pore properties, both spherical and irregular shaped carbamide with different particle size ranges were used as ...
Mutlu, Ilven, Oktay, Enver
openaire +2 more sources
Strength Properties of 316L and 17-4 PH Stainless Steel Produced with Additive Manufacturing. [PDF]
Materials (Basel), 2022 The number of additive manufacturing methods and materials is growing rapidly, leaving gaps in the knowledge of specific material properties. A relatively recent addition is the metal-filled filament to be printed similarly to the fused filament fabrication (FFF) technology used for plastic materials, but with additional debinding and sintering steps ...
Kedziora S +6 more
europepmc +4 more sources
Processing and properties of highly porous 17-4 PH stainless steel
Powder Metallurgy and Metal Ceramics, 2011 Highly porous 17-4 PH stainless steel having porosities in the range of 39–82% with an average pore size of around 700 μm was successfully fabricated using space holder technique in powder metallurgy. Irregular carbamide particles were used as a space holder material. The final porosity was directly related to the added fraction of carbamide.
Mutlu, Ilven, Oktay, Enver
openaire +2 more sources