Results 161 to 170 of about 2,704,947 (212)

Additive manufacturing of 17-4PH stainless steel

2nd International PhD Student’s Conference at the University of Life Sciences in Lublin, Poland: ENVIRONMENT – PLANT – ANIMAL – PRODUCT, 2023
Aleksander Świetlicki, Mariusz Walczak, Mirosław Szala   +2 more
openaire   +1 more source

Excellent tension properties of stainless steel with a 316L/17-4PH/17-4PH laminated structure fabricated through laser additive manufacturing

Materials Science and Engineering: A, 2022
Kang Xu, Bochuan Li, Simeng Li, Ronghua Chen, Xingke Gao, Chenghuan Liu, Chao Jiang, Lijun Song   +7 more
openaire   +1 more source

Effect of scanning speed on laser deposited 17-4PH stainless steel

2017 8th International Conference on Mechanical and Intelligent Manufacturing Technologies (ICMIMT), 2017
Laser metal deposition (LMD) is one of the additive manufacturing technologies that is used in the production of fully dense parts layer by layer. This innovative manufacturing process has the potential to reduce the weight, time and cost of manufacturing components.
Abiodun Bayode, Sisa Pityana, Esther Titilayo Akinlabi, Mxolisi Brendon Shongwe   +3 more
openaire   +1 more source

Hydrogen-Assisted Fracture of a 17-4PH Airplane Wing Component

1992
Abstract Cracks were discovered in the cast 17-4 PH stainless steel outboard leading edge flap support of an aircraft wing during overhaul inspection. Failure analysis focused on an apparently intergranular area of fracture surface. It was determined that the original mode of crack growth was cleavage, probably caused by cast-in hydrogen.
openaire   +1 more source

On the relation between microstructure and impact toughness of 17-4PH stainless steel produced by powder bed fusion laser beam (PBF-LB)

Materials Science & Engineering: A
This work investigated the effects of aging heat treatments on the microstructure and, consequently, the quasi-static (tensile properties) and dynamic (impact toughness) mechanical behaviour of a 17-4 PH stainless steel produced by powder bed fusion ...
Renata De Oliveira Melo, Jean-Bernard Vogt, Eric Nivet, F. Villaret, Christophe Grosjean, E. Baustert, N. Tran, J. Bouquerel, Gang Ji   +8 more
semanticscholar   +1 more source

Analysis of Additively Manufactured 17-4PH Stainless Steel

2019
Master of Applied Science (MASc)
openaire   +1 more source

Vibration characteristics of 17-4PH metal material extrusion thin plates

Rapid Prototyping Journal
Purpose The purpose of this study is to set up the theoretical model for predicting the vibration characteristics of 17-4PH metal material extrusion (MME) green and sintered parts, as well as carry out the experimental validation and sensitivity analysis.
Shijie Jiang, Yuntao Zhang, Shuo Liu, Shanggang Cai, Hongwei Ying, Jiaqi Chen   +5 more
openaire   +1 more source

Fused filament fabrication and sintering of 17-4PH stainless steel

Manufacturing Letters, 2022
Yaozhong Zhang, Aljoscha Roch
openaire   +1 more source

High Efficiency Surface Finishing of Direct Energy Deposition Manufactured 17‐4PH Stainless Steel: Roughness Reduction and Corrosion Protection

Steel Research International
Additive manufacturing (AM) of metallic parts has gained significant attention in the materials manufacturing industry. Despite the advantages of complex shape, flexibility, rapid prototyping, and ease of processing, AM parts have associated ...
Jothi Prakash Chakrapani Gunarasan, Dong-Gyu Ahn, Jeong‐Won Lee   +2 more
semanticscholar   +1 more source

MECHANICAL PROPERTIES OF 17-4PH STEEL, HOMOGENIZED VERSUS AS RECEIVED CONDITION

1964
Abstract : For the particular heat of 17-4PH steel plate involved, homogenizing treatment improved the ductility as measured by the reduction of area and reduced the spread in ductility data ,or each aged condition. (Author)
openaire   +1 more source