Results 51 to 60 of about 3,834,829 (197)
3D printed hernia mesh implant: a conformability study [PDF]
Exploration of BioMat-XAim: This study aims to explore the sensing capabilities of polyvinylidene fluoride-hydroxyapatite-chitosan (PVDF-HAP-CS) composite-based hernia mesh implants (of conformal/planar design), followed by in-vitro analysis for better understanding of the bio-
Abhishek Barwar +3 more
doaj +1 more source
Shot Peening Effect on Sliding Wear in 0.9% NaCl of Additively Manufactured 17-4PH Steel. [PDF]
Materials (Basel)The growing demand for modern steels showing corrosion and tribological resistance has led to their increased use in the production of medical devices.
Walczak M +4 more
europepmc +2 more sources
Effects of Cu Content on the Corrosion Resistance and Antibacterial Property of Low Carbon Steels [PDF]
Cailiao Baohu, 2023 Low carbon steels require not only high strength and hardness，but also good corrosion resistance and antibacterial property.In order to study the corrosion resistance and antibacterial property of different low carbon steels with different Cu contents
YU Shuo-shuo, XU Zheng-meng, TANG Yuan-shou, SI Yu, ZHOU Xin, YANG Hao-cheng, LI Ke-jian, MA Yi-long, GE Yi-bo
doaj +1 more source
Effect of Laser Solution-Aging Process Parameters on the Hardness and Water Erosion Resistance of 17-4PH Stainless Steel [PDF]
Cailiao BaohuTo address the issues of the last-stage blades of steam turbines being susceptible to pitting，water erosion and even fracture，surface laser solution-aging strengthening treatment was carried out on 17-4PH precipitation-hardened stainless steel using a ...
LI Yongke, XUE Xiang, LI Yong, WANG Xiaoen, LIU Gang, XIE Weiwei, WANG Mingyuan
doaj +1 more source
Tribological properties of the QAL9-4 and 17-4PH textured friction pair with water lubrication
AIP Advances, 2021 To study the lubrication and wear reduction characteristics of the QAL9-4 and 17-4pH textured friction pair during water lubrication, the dynamic pressure bearing and cavitation characteristics were analyzed using a computational fluid dynamics method ...
Tao He +6 more
doaj +1 more source
Fatigue life optimization for 17-4Ph steel produced by selective laser melting
, 2022 International audiencePurpose: The mechanical characterization of Selective Laser Melting (SLM) parts is an industrial challenge. In this paper, a methodology is proposed to control the fatigue life of 17-4Ph stainless steel by selecting the most ...
Chaves-Jacob, Julien +3 more
core +1 more source
Effect of Porosity on Ductility Variation in Investment Cast 17-4PH [PDF]
Microscopy and Microanalysis, 2005 The stainless steel alloy 17-4PH contains a martensitic microstructure and second phase delta ({delta}) ferrite. Strengthening of 17-4PH is attributed to Cu-rich precipitates produced during age hardening treatments at 900-1150 F (H900-H1150). For wrought 17-4PH, the effects of heat treatment and microstructure on mechanical properties are well ...
D Susan +4 more
openaire +1 more source
Influence of hydrogen on the stress-relaxation properties of 17-4PH martensitic stainless steel manufactured by laser powder bed fusion [PDF]
, 2022 To evaluate the interactions between hydrogen and the mechanical behavior of additively manufactured (AM) 17-4PH martensitic stainless steel (MSS), stress-relaxation tests were performed for both non-charged and hydrogen-charged samples.
Blanc, Christine +5 more
core +1 more source
Earthquake Engineering &Structural Dynamics, Volume 55, Issue 14, Page 3593-3611, November 2026.ABSTRACT Considering the needs for reducing carbon emissions and except for extreme cases of very degraded existing structures, research on technologies allowing continued use or upgrading of older buildings has become a priority topic. Generally, research on upgrading of reinforced concrete frame structures certainly has a prominent role, because of ...
Francesco Nigro +2 more
wiley +1 more source
Bending Fatigue Behavior of 17-4 PH Gears Produced by Additive Manufacturing
Applied Sciences, 2021 The introduction of Additive Manufacturing (AM) is changing the way in which components and machines can be designed and manufactured. Within this context, designers are taking advantage of the possibilities of producing parts via the addition of ...
Franco Concli +6 more
doaj +1 more source