Results 21 to 30 of about 3,775,940 (194)
Effects of ageing heat treatment temperature on the properties of DMLS additive manufactured 17-4PH steel [PDF]
Bulletin of the Polish Academy of Sciences: Technical Sciences, 2023 Additive manufacturing (AM) is a modern, innovative manufacturing method that enables the production of fully dense products with high mechanical properties and complex shapes that are often impossible to obtain by traditional methods.
Aleksander Świetlicki +4 more
doaj +4 more sources
17-4PH stainless steel fastener for high salt fog open-air marine coupling. [PDF]
PLoS ONEThe C01 type diaphragm coupling demonstrates effective performance in high-concentration seawater salt fog environments. However, the fastener material for this coupling must possess high mechanical properties and strong resistance to seawater corrosion.
Angang Cao, Tao Yu, Yigui Lu, Wei Li
doaj +2 more sources
The Effect of Aging Treatment on the Corrosion Behavior of 17-4PH Stainless Steel. [PDF]
Materials (Basel)This study systematically investigated the influence of aging temperature variations on the evolution of Cu-rich precipitates and dislocation distribution characteristics in 17-4PH stainless steel through comprehensive electrochemical testing and microstructural characterization.
Zhou C, Lv Y, Zhang L.
europepmc +3 more sources
Cailiao gongcheng, 2018 The stress corrosion cracking (SCC) behavior and mechanism of M152 and 17-4PH high-strength steels in high Cl- environment were studied through neutral salt spray test and slow strain rate tensile (SSRT) test. The result shows that M152 and 17-4PH steels
WU Wei +6 more
doaj +2 more sources
Metals, 2022 Samples of 17-4PH high-strength steel were processed by selective laser melting (SLM) and solution-processed. The effects of the solution temperature on the microstructure and mechanical properties of the samples were studied.
Pengcheng Huo +2 more
exaly +3 more sources
High cycle torsional fatigue properties of 17-4PH stainless steel [PDF]
Fracture and Structural Integrity, 2016 Sensitivity to small defects under torsional fatigue loading condition is examined in the high cycle fatigue regime. Fatigue crack initiation and small crack growth behaviors were observed during fatigue testing and fractographic investigations were ...
K. Yanase, B.M. Shönbauer, M. Endo
doaj +6 more sources
Metals, 2021 Residual stress is a crucial element in determining the integrity of parts and lifetime of additively manufactured structures. In stainless steel and Ti-6Al-4V fabricated joints, residual stress causes cracking and delamination of the brittle ...
Nana Kwabena Adomako +4 more
doaj +2 more sources
Effects of solution treatment, precipitation hardening, and shot peening on the cavitation erosion resistance of 17‑4PH steel produced by additive and conventional methods [PDF]
Scientific Reports17-4PH stainless steel is widely used in hydraulic components exposed to cavitation, yet its cavitation erosion resistance (CER) depends strongly on both the manufacturing route and the applied post-processing.
Aleksander Świetlicki +3 more
doaj +2 more sources
Microstructure and performance of laser cladding 17-4PH-xTiC coatings on harvester blades. [PDF]
PLoS OneTo address the need for extending the service life of combine harvester blades, this study employs laser cladding technology to prepare 17–4PH-xTiC coatings with varying TiC content on 65Mn steel substrates. The effect of TiC content on the microstructure and properties of the coatings was investigated.
Luo DY +5 more
europepmc +3 more sources
A Review of the Mechanical Properties of 17-4PH Stainless Steel Produced by Bound Powder Extrusion [PDF]
Journal of Manufacturing and Materials Processing, 2023 17-4PH Stainless Steel is a mechanically high-performing alloy that is widely used across chemical and mechanical processing industries. The alloy is conventionally fabricated by cast methods, but emerging additive manufacturing techniques are presently ...
Jaidyn Jones, Ana Vafadar, Reza Hashemi
doaj +2 more sources