Results 81 to 90 of about 2,704,947 (212)

Additively manufactured 17–4 PH stainless steels for fracture management devices

Virtual and Physical Prototyping
Stainless steel 316L (SS316L) is widely used in fracture management devices. However, SS316L does not offer any bacterial infection resistance and can cause metal-ion sensitivity due to Ni-ions’ presence.
Aruntapan Dash, Susmita Bose, Amit Bandyopadhyay   +2 more
doaj   +1 more source

Experimental study on deep hole drilling of 17-4PH material

IOP Conference Series: Materials Science and Engineering, 2018
This paper uses 17-4PH material as the research object, according to the material characteristics of 17-4PH, designed and carried out deep hole drilling test. The purpose of the experiment is to study and discuss the three major problems of tool wear, chip shape and axial deviation of the hole in the process of deep hole drilling of 17-4PH materials ...
LI Uzhanfeng, LI Uquantai
openaire   +1 more source

Corrosion Behavior of Additively Manufactured Steels: A Comprehensive Review

steel research international, Volume 96, Issue 10, Page 51-79, October 2025.
This review explores the corrosion behavior of various steel types, including austenitic, martensitic, duplex, low‐alloy, and maraging steels, produced via additive manufacturing (AM). It discusses how AM impacts material properties, such as grain structure and the formation of defects like porosity, and highlights the importance of optimizing process ...
Eneko Villabona, Fernando Veiga, Pedro José Rivero, Virginia Uralde, Alfredo Suárez   +4 more
wiley   +1 more source

A Statistical Review of Hydrogen Effects on the Fatigue and Fracture Behavior of Steel

Fatigue &Fracture of Engineering Materials &Structures, Volume 48, Issue 9, Page 3613-3644, September 2025.
ABSTRACT This study conducts a statistical re‐analysis of experimental data from the literature to assess the influence of hydrogen on key mechanical properties, including the medium‐/high‐cycle fatigue strength and the threshold value of the stress intensity factor range.
H. Wang, N. O. Larrosa, D. Engelberg, R. Best, L. Susmel   +4 more
wiley   +1 more source

Corrosion Fatigue of 17-4pH Stainless Steel in a Simulated Sea Water Solution

Journal of Advanced Materials in Engineering, 2019
Since martensitic precipitation hardened 17-4pH stainless steel has been widely used in corrosive environments, evaluation of its corrosion fatigue behavior is important. In this research, after microstructural studies, mechanical, corrosion, fatigue and
M. Ghasemian Malakshah, F. Ashrafizadeh, A. Eslami, F. Fadaeifard   +3 more
doaj  

Probing Anisotropic Quasiparticle Dynamics and Topological Phase Transitions in Quasi‐1D Topological Insulator ZrTe5

Advanced Science, Volume 12, Issue 31, August 21, 2025.
This study reveals quasiparticle dynamics in ZrTe5. Polarization‐dependent measurements show transient reflectivity anisotropy arises from electron relaxation and lattice vibrations. The first dynamical evidence of a temperature‐induced Lifshitz transition is reported.
Yueying Hou, Linze Li, Sutao Sun, Gan Liu, Hongyuan Zhao, Zhiheng Chen, Xuejun Yan, Yang‐Yang Lv, Yurong Yang, Shu‐Hua Yao, Jian Zhou, Y.B. Chen, Ming‐Hui Lu, Vitalyi Gusev, Yan‐Feng Chen   +14 more
wiley   +1 more source

Single‐Molecule Multi‐Channel Conductance Assisted by Through‐Space Conjugation

SmartMat, Volume 6, Issue 3, June 2025.
Through‐space (TS) conjugation has been recognized as an effective charge transport channel in molecular electronics. In‐depth understanding of functions and mechanisms of TS channels in multi‐channel circuits is of high importance. This review introduces advances in charge transport systems from a molecular topology perspective, focusing on multi ...
Shaoxin Song, Jinshi Li, Yi Xiong, Ben Zhong Tang, Zujin Zhao   +4 more
wiley   +1 more source

Mass transport and porous structure evolution during solvent debinding of additively manufactured stainless steel

Virtual and Physical Prototyping
Material extrusion (ME) based additive manufacturing has gained much attention as a cost-effective method for the fabrication of complex metal components, particularly using 17-4PH stainless steel.
Yulin Liu, Audai Al-Akailah, Fuda Ning
doaj   +1 more source

Production of D2 and 17-4 PH Bimetallic Materials and Investigation of Their Mechanical Properties in Atomic Diffusion Additive Manufacturing Method

Gazi Üniversitesi Fen Bilimleri Dergisi
The study focused on the production of bimetallic material from 17-4 stainless steel and D2 tool steel using the Markforged brand Metal X device. In particular, despite the different physical and mechanical properties of the materials used, studies were ...
Ufuk Taşcı
doaj   +1 more source

Coupled Heat Transfer Analysis of Hypersonic Wide-Speed-Range Cruise Aircraft

Aerospace
Hypersonic aircraft represent a cutting-edge technology in aerospace engineering. Coupled heat transfer is a critical physical phenomenon in such aircraft. However, existing studies face challenges in predicting aerothermal behavior.
Shuailong Gao, Zhiyuan Ai, Shaojie Ma, Kunming Jia, Lin Gan   +4 more
doaj   +1 more source