Results 181 to 190 of about 4,567,195 (228)
Some of the next articles are maybe not open access.
Materials letters (General ed.), 2019
Material extrusion additive manufacturing can be used for producing metal specimens when combined with debinding and sintering, similar to metal injection moulding.
J. Gonzalez-Gutierrez +4 more
semanticscholar +1 more source
Material extrusion additive manufacturing can be used for producing metal specimens when combined with debinding and sintering, similar to metal injection moulding.
J. Gonzalez-Gutierrez +4 more
semanticscholar +1 more source
Effect of ECAP on the Microstructure and Mechanical Properties of 17-4PH Stainless Steel
Materials Science Forum, 2010Experiments were conducted to evaluate the influence of equal-channel angular pressing (ECAP) on the microstructure and mechanical properties of 17-4PH steel. The 17-4PH steel was solution-treated at 1040°C for 1h followed by oil cooling before ECAP process.
Gang Yang, Feng Shi Yin
openaire +1 more source
Additive manufacturing of 17-4PH stainless steel
2nd International PhD Student’s Conference at the University of Life Sciences in Lublin, Poland: ENVIRONMENT – PLANT – ANIMAL – PRODUCT, 2023Aleksander Świetlicki +2 more
openaire +1 more source
The Effect of Thermomechanical Treatment On Pitting Corrosion of 17-4PH Stainless Steel
ECS Meeting Abstracts, 2013Abstract not Available.
Mozhgan Abooei Mehrizi +1 more
openaire +1 more source
Journal of tribology
Cavitation erosion caused by bubble collapse due to pressure fluctuations is a common phenomenon in critical components such as steam turbines, centrifugal pumps, ship propellers, turbine blades, valves, and engine cylinder liners.
J. Di +5 more
semanticscholar +1 more source
Cavitation erosion caused by bubble collapse due to pressure fluctuations is a common phenomenon in critical components such as steam turbines, centrifugal pumps, ship propellers, turbine blades, valves, and engine cylinder liners.
J. Di +5 more
semanticscholar +1 more source
Inhibitive Effect of Nitrate on Pitting Corrosion of 17-4PH Stainless Steel
Corrosion, 2016In this work, the inhibition effect of nitrate on the pitting corrosion of 17-4PH stainless steel was investigated in the chloride solution. Potentiodynamic and potentiostatic techniques were used to measure the pitting potential and induction time in various concentrations of chloride and nitrate ions.
M. Seyedi +4 more
openaire +1 more source
Influence of Sulfur Content on the Corrosion Resistance of 17-4PH Stainless Steel
Journal of Materials Engineering and Performance, 2017According to specification standards, the basic chemical composition of steel 17-4PH for special and critical applications is 15-17% Cr, 3.0-5.0% Ni, 3.0-5.0% Cu, 0.07% C (max) and 0.15-0.45% (Nb + Ta) (wt.%). The maximum sulfur content is 0.030%. However, as it will be shown in this work, this maximum limit for sulfur is too high for services where ...
S. S. M. Tavares +3 more
openaire +1 more source
EFFECT OF CASTING DEFECT ON MECHANICAL PROPERTIES OF 17-4PH STAINLESS STEEL
International Journal of Modern Physics B, 2006Damage and integrity evaluation techniques should be developed steadily in order to ensure the reliability and the economic efficiency of gas turbine engines. Casting defects may exist in most casting components of gas turbine engines, and the defects could give serious effect on mechanical properties and fracture toughness.
JONG-YUP KIM +2 more
openaire +1 more source
Influence of Feed Variation on Tool Wear When Milling Stainless Steel 17-4Ph
Journal of Engineering for Industry, 1994This paper presents the results of experimental studies on the influence of feed variation on tool wear during face milling. Experimental results on milling Stainless Steel 17-4PH show that it is possible to increase tool life substantially with a proper variation of the cutting feed rate throughout the cutting process.
E. Ennajimi, M. Balazinski
openaire +2 more sources
Journal of Micromanufacturing
Since the field’s founding, understanding metal additive manufacturing (AM) procedures and the composition and characteristics of the produced metallic components has come a long way.
M. Hossain +4 more
semanticscholar +1 more source
Since the field’s founding, understanding metal additive manufacturing (AM) procedures and the composition and characteristics of the produced metallic components has come a long way.
M. Hossain +4 more
semanticscholar +1 more source