Mechanical properties of 17-4PH stainless steel foam panels [PDF]
Materials Science and Engineering: A, 2007 Rectangular 17-4PH stainless steel sandwiched foam panels were fabricated using a commercial manufacturing technique by brazing two sheets to a foam core. Microstructural observations and ultrasonic nondestructive evaluation of the panels revealed large variations in the quality of the brazed areas from one panel to the next as well as within the same ...
S.V. Raj +5 more
openaire +3 more sources
Effects of solution treatment, precipitation hardening, and shot peening on the cavitation erosion resistance of 17‑4PH steel produced by additive and conventional methods [PDF]
Scientific Reports17-4PH stainless steel is widely used in hydraulic components exposed to cavitation, yet its cavitation erosion resistance (CER) depends strongly on both the manufacturing route and the applied post-processing.
Aleksander Świetlicki +3 more
doaj +2 more sources
Additively manufactured 17–4 PH stainless steels for fracture management devices [PDF]
Virtual and Physical PrototypingStainless steel 316L (SS316L) is widely used in fracture management devices. However, SS316L does not offer any bacterial infection resistance and can cause metal-ion sensitivity due to Ni-ions’ presence.
Aruntapan Dash +2 more
doaj +2 more sources
Electrochemical Corrosion Behaviors of 17 - 4PH Stainless Steel in Different Concentrations of HCl Solutions [PDF]
Cailiao Baohu, 2021 In order to explore the corrosion behavior of 17 - 4PH stainless steel in HCl solution, the corrosion performance of 17 - 4PH stainless steel in HCl solution was measured by potentiodynamic polarization and electrochemical impedance.
CHENG Jian - guo, LIU Zhen, ZHAO Shi - guang, PAN Ai - sheng, JIAN Ji, SI Ting - zhi
doaj +1 more source
Experimental assessment of ferritic stainless steel composite slabs [PDF]
, 2013 This paper describes investigations into the structural behaviour of ferritic stainless steel floor decking in composite construction. Although commonly used in the automotive and industrial sectors, structural applications of ferritic stainless steels ...
Cashell, K
core +6 more sources
Finite element modelling of cold formed stainless steel columns [PDF]
, 2004 This paper describes the results obtained from a finite element investigation into the load capacity of column members of lipped channel cross-section, cold formed from Type 304 stainless steel, subjected to concentric and eccentric compression loading ...
Rhodes, J., Macdonald, M.
core +5 more sources
A review on the production of 17-4PH parts using press and sinter technology
Science Progress, 2023 The press and sinter method remains the standard among powder metallurgy processes for powdered stainless-steel materials. It delivers low cost, low oxidation rate, and adequate corrosion resistance.
Mohammed Qasim Kareem +3 more
doaj +1 more source
Metals, 2021 Residual stress is a crucial element in determining the integrity of parts and lifetime of additively manufactured structures. In stainless steel and Ti-6Al-4V fabricated joints, residual stress causes cracking and delamination of the brittle ...
Nana Kwabena Adomako +4 more
doaj +1 more source
Hydrogen Embrittlement Susceptibility of Super Duplex Stainless Steels [PDF]
, 2010 This thesis describes the metallurgical and environmental factors that influence hydrogen embrittlement of super duplex stainless steels and presents a model to predict the rate at which embrittlement occurs.
Alsarraf, Jalal
core +7 more sources
Nonlinear ultrasonic characterization of precipitation in 17-4PH stainless steel [PDF]
NDT & E International, 2015 Abstract This research is part of a broader effort to develop a nondestructive evaluation technique to monitor radiation damage in reactor pressure vessel steels, the main contributor being copper-rich precipitates. In this work, 17-4PH stainless steel is thermally aged to study the effects of copper precipitates on the acoustic nonlinearity ...
Matlack, Kathryn H. +7 more
openaire +1 more source