Results 171 to 180 of about 63,490,372 (207)

Failure Analysis of a 17-4PH Stainless Steel Part in an Exhaust Fastener

Journal of Failure Analysis and Prevention, 2021
Despite high level of attention in the process of making metallic fasteners, failure of the fasteners happens in various industries. Sometimes, failures are recognized during the quality control checks in the companies. During a batch of production and during assembly test, failure of a 17-4PH stainless steel part in an exhaust fastener was seen.
Masoud Yousefi, Masoud Rajabi, Mahnaz Yousefi, Mohamammad Sadegh Amiri Kerahroodi   +3 more
openaire   +1 more source

Microstructures, properties, and applications of laser sintered 17‐4PH stainless steel

Journal of the American Ceramic Society, 2019
Abstract The effects of hot isostatic pressing (HIP) on the densification, mechanical properties, and microstructures of laser‐powder bed fusion (L‐PBF) 17‐4 PH stainless steel parts were studied using gas‐ and water‐atomized powders. The % theoretical density, ultimate tensile strength, yield strength, elongation,
Harish Irrinki, Subrata Deb Nath, Magnus Alhofors, Jason Stitzel, Ozkan Gulsoy, Sundar V. Atre   +5 more
openaire   +2 more sources

Weldability of 17-4PH stainless steel in overaged heat treated condition

Science and Technology of Welding and Joining, 2006
Studies on the weldability of 17-4PH stainless steel, in the 621°C overaged condition, showed that Creq/Nieq ratio higher than 1·5 resulted in primary ferritic mode of solidification in the weld metal. Post-weld aging treatment at 482°C enhanced the strength of the weld joint with corresponding reduction in impact toughness of the weld metal while ...
C. R. Das, H. C. Dey, G. Srinivasan, S. K. Albert, A. K. Bhaduri, A. Dasgupta   +5 more
exaly   +2 more sources

The modification of corrosion resistance of 17-4PH stainless steel by cutting process

Journal of Manufacturing Processes, 2020
Abstract It is well-known that taking high-speed dry cutting as the final process of manufacture is a new kind of green manufacturing technology. However, the service performance of the machined components must be evaluated before applying this new technique to industry widely.
Guoliang Liu, Chuanzhen Huang, Bin Zou, Hanlian Liu, Zhanqiang Liu, Yue Liu, Chengwu Li   +6 more
openaire   +1 more source

Effect of scanning speed on laser deposited 17-4PH stainless steel

2017 8th International Conference on Mechanical and Intelligent Manufacturing Technologies (ICMIMT), 2017
Laser metal deposition (LMD) is one of the additive manufacturing technologies that is used in the production of fully dense parts layer by layer. This innovative manufacturing process has the potential to reduce the weight, time and cost of manufacturing components.
Abiodun Bayode, Sisa Pityana, Esther Titilayo Akinlabi, Mxolisi Brendon Shongwe   +3 more
openaire   +1 more source

Rotary friction welding of additively manufactured 17-4PH stainless steel

Journal of Manufacturing Processes, 2021
Abstract The aim of the present study is to investigate the effect of rotary friction welding (RFW) on the microstructure, tensile properties, hardness, wear resistance and corrosion properties of the weld joint of an additively manufactured solid cylinder made of 17-4PH stainless steel.
H.R. Lashgari, S. Li, C. Kong, M. Asnavandi, Sh. Zangeneh   +4 more
openaire   +1 more source

Effect Of Cold Deformation On Pitting Initiation Of 17-4PH Stainless Steel

ECS Meeting Abstracts, 2013
Abstract not Available.
Davood Nakhaie, Mohammad Hadi Moayed
openaire   +1 more source

Microstructure and hardness investigation of 17-4PH stainless steel by laser quenching

Materials Science and Engineering: A, 2012
Abstract Surface hardening of 17-4PH was achieved by laser transformation hardening using 5 kW continuous wave CO 2 laser system. The microstructure of the laser-quenched sample was investigated by optical microscopy, transmission electron microscope and 57 Fe Mossbauer spectrometer. The hardness profile was determined by a Vickers hardness tester.
Zhaoyun Chen, Guijuan Zhou, Zhonghua Chen   +2 more
openaire   +1 more source

Experimental investigation on selective laser melting of 17-4PH stainless steel

Optics & Laser Technology, 2017
Abstract Selective laser melting (SLM) is an additive manufacturing (AM) technique that uses powders to fabricate 3Dparts directly. The objective of this paper is to perform an experimental investigation of selective laser melted 17-4PH stainless steel. The investigation involved the influence of separate processing parameters on the density, defect,
Zhiheng Hu, Haihong Zhu, Hu Zhang, Xiaoyan Zeng   +3 more
openaire   +1 more source

Effect of ECAP on the Microstructure and Mechanical Properties of 17-4PH Stainless Steel

Materials Science Forum, 2010
Experiments were conducted to evaluate the influence of equal-channel angular pressing (ECAP) on the microstructure and mechanical properties of 17-4PH steel. The 17-4PH steel was solution-treated at 1040°C for 1h followed by oil cooling before ECAP process.
Gang Yang, Feng Shi Yin
openaire   +1 more source