Results 111 to 120 of about 4,105 (209)

Wear maps for TiC composite based coatings deposited on 303 stainless steel

, 2014
Dry sliding wear (pin-on-disc) tests were carried out under ambient conditions at room temperature for TiC coated and uncoated 303 stainless steel, using alumina as a counterface.
Rasool, Ghulam, Stack, Margaret, Stack, M.M., Rasool, G.   +3 more
core   +1 more source

Sub-Zero Temperature Effect on Impact Properties of 17-4PH Stainless Steel Processed by Selective Laser Melting

, 2017
The Selective Laser Melting (SLM) process has been proved as the most effective method among Additive Manufacturing (AM) technologies to produce hard, dense and strong metallic structures with intricate shapes and profiles from wide range of metallic ...
Ashish M. Ashok, Syed H. Riza, Syed H. Masood, Igor Sbarski   +3 more
core   +1 more source

Feasibility of Fabricating Metal Parts from 17-4PH Stainless Steel Powder

, 1998
17-4 PH stainless steel is known to provide an attractive combination of high strength and corrosion resistance. In this research, the feasibility of SFF fabrication of high density parts using PH powder is examined. A part can be fabricated using both
Wu, Guohua, Sadangi, Rajendra, Danforth, Stephen C., Rangarajan, Sriram, Safari, Amhad, Langrana, Noshir   +5 more
core   +1 more source

Electrochemical behavior of injection molded gas and water atomized 17-4PH stainless steel powder

, 2017
This paper describes the electrochemical behavior of injection molded 17-4PH stainless steel gas and water atomized powder. Gas and water atomized stainless steel powders were injection molded with wax based binder.

core  

86th Annual Meeting of the Meteoritical Society (2024)

Meteoritics &Planetary Science, Volume 59, Issue S1, Page A1-A468, August 2024.
wiley   +1 more source

Alternative to Nitric Acid Passivation of 15-5 and 17-4PH Stainless Steel Using Electrochemical Techniques. [PDF]

Materials (Basel), 2020
Lara-Banda M, Gaona-Tiburcio C, Zambrano-Robledo P, Delgado-E M, Cabral-Miramontes JA, Nieves-Mendoza D, Maldonado-Bandala E, Estupiñan-López F, G Chacón-Nava J, Almeraya-Calderón F.   +9 more
europepmc   +1 more source

Extremely Low Cycle Fatigue Behavior of Additively Manufactured 17-4PH Stainless Steel

, 2020
Steel structures survive seismic loading thanks to components capable of dissipating large amounts of energy through large deformations. Future optimizations of these components include complex free-form geometries that are difficult to fabricate with ...
Collins, Kaley
core   +1 more source

Optimization of the 3D Printing Parameters for Tensile Properties of Specimens Produced by Fused Filament Fabrication of 17-4PH Stainless Steel. [PDF]

Materials (Basel), 2020
Godec D, Cano S, Holzer C, Gonzalez-Gutierrez J.   +3 more
europepmc   +1 more source

Mechanical and metrological characterisation of 17-4PH stainless steel structures processed by material extrusion additive manufacturing

Journal of Materials Research and Technology
Additive manufacturing (AM) has progressed from its initial use in prototyping to the fabrication of fully functional components. However, the performance characteristics of parts produced by these techniques are still under investigation.
Ana Romero, Miguel A. Caminero, Eustaquio García-Plaza, Pedro J. Núñez, Jesús M. Chacón, Gloria P. Rodríguez, Antonio Cañadilla, Juan L. Martínez   +7 more
doaj   +1 more source

Correction: Lara-Banda, M., et al. Alternative to Nitric Acid Passivation of 15-5 and 17-4PH Stainless Steel Using Electrochemical Techniques. Materials 2020, 13, 2836. [PDF]

Materials (Basel), 2020
Lara-Banda M, Gaona-Tiburcio C, Zambrano-Robledo P, Delgado-E M, Cabral-Miramontes JA, Nieves-Mendoza D, Maldonado-Bandala E, Estupiñan-López F, Chacón-Nava JG, Almeraya-Calderón F.   +9 more
europepmc   +1 more source