Results 81 to 90 of about 387 (167)

Interlayer Tailoring of Ti-6Al-4V and 17-4PH Stainless Steel Joint by Tungsten Inert Gas Welding. [PDF]

Materials (Basel), 2023
Hajra RN, Park CW, Choi K, Kim JH.
europepmc   +1 more source

Strengthening mechanisms of stress rupture performance in additive-manufactured 17-4PH stainless steel

Virtual and Physical Prototyping
To obtain the desired microstructures in laser powder bed fusion 17-4PH stainless steel for multifunctional performance demands, this study optimised the microstructure and mechanical behaviour under extreme service conditions of elevated temperatures ...
Rongrong Huang, Hongyun Zhao, Yazhou Liu, Rui Ma, Yiming Sun, Jianhui Su, Danyang Lin, Bo Chen, Xiaoguo Song, Swee Leong Sing, Caiwang Tan   +10 more
doaj   +1 more source

Effect of TiC Content on Microstructure and Wear Performance of 17-4PH Stainless Steel Composites Manufactured by Indirect Metal 3D Printing. [PDF]

Materials (Basel), 2023
Huang X, Mei S, Li Y, Li M, Zhou S, Shang H.   +5 more
europepmc   +1 more source

Mass transport and porous structure evolution during solvent debinding of additively manufactured stainless steel

Virtual and Physical Prototyping
Material extrusion (ME) based additive manufacturing has gained much attention as a cost-effective method for the fabrication of complex metal components, particularly using 17-4PH stainless steel.
Yulin Liu, Audai Al-Akailah, Fuda Ning
doaj   +1 more source

Sintering Behavior of Bi-Material Micro-Component of 17-4PH Stainless Steel and Yttria-Stabilized Zirconia Produced by Two-Component Micro-Powder Injection Molding Process. [PDF]

Materials (Basel), 2022
Basir A, Sulong AB, Jamadon NH, Muhamad N.   +3 more
europepmc   +1 more source

3D printing conditions determination for feedstock used in fused filament fabrication (FFF) of 17-4PH stainless steel parts

Metalurgija, 2018
Fused filament fabrication combined with debinding and sintering could be an economical process for 3D printing of metal parts. In this study, compounding, filament making and FFF processing of a feedstock material containing 55 vol.
J. Gonzalez-Gutierez, D. Godec, R. Guráň, M. Spoerk, C. Kukla, C. Holzer   +5 more
doaj  

Effects of Time on Microstructure and Erosion Corrosion behaviour of Liquid nitrided 17-4PH stainless steel

工程科学与技术, 2013
:Liquid nitriding of 17-4 PH martensitic precipitation hardening stainless steels was conducted at 430 °C for different time using a complex chemical heat-treatment, and the erosion corrosion resistance of the nitrided samples was evaluated. Experimental
wang jun
doaj  

Data-driven parameter optimization for bead geometry in wire arc additive manufacturing of 17-4 PH stainless steel

Journal of Advanced Joining Processes
Due to its high strength, corrosion resistance, and toughness, 17-4 Precipitation Hardening (PH) stainless steel is widely used in aerospace, petrochemical, and marine industries. Additive manufacturing (AM) technologies enable the fabrication of complex
Muhammad Irfan, Yun-Fei Fu, Shalini Singh, Sajid Ullah Butt, Abul Fazal Arif, Osezua Ibhadode, Ahmed Qureshi   +6 more
doaj   +1 more source

Laser deposition additive manufacturing of 17-4PH stainless steel on Ti-6Al-4V using V interlayer

Materials Research Letters, 2019
For the first time, additive manufacturing was used to obtain a strong joint (bonding strength >200 MPa) between stainless steel and Ti-6Al-4V using a V interlayer.
Nana Kwabena Adomako, Sanghoon Noh, Chang-Seok Oh, Sangsun Yang, Jeoung Han Kim   +4 more
doaj   +1 more source

Plasma debinding and sintering of metal injection moulded 17-4PH stainless steel

Materials Research, 2011
In this work, 17-4PH stainless steel parts processed in a Plasma Assisted Debinding and Sintering (PADS) furnace were characterised in terms of microstructure, final density, microhardness, carbon content and tensile behaviour. To determine whether these
Renan Schroeder, Gisele Hammes, Cristiano Binder, Aloisio Nelmo Klein   +3 more
doaj