Results 101 to 110 of about 63,490,372 (207)

Optimization of Aging Temperature and Heat-Treatment Pathways in Additively Manufactured 17-4PH Stainless Steel. [PDF]

Materials (Basel), 2023
Chae H, Lim S, Lee T, Shin E, Suh J, Kang SH, Lee SY.   +6 more
europepmc   +1 more source

Corrosion Behaviour of 304 Austenitic, 15-5PH and 17-4PH Passive Stainless Steels in acid solutions

International Journal of Electrochemical Science, 2018
The objective of this work was to study is use electrochemical techniques to determinate the growth conditions, characteristics and resistance of passive layers of stainless steel (SS): 304 austenitic, 17-4PH (precipitation hardening) and 15-5PH ...
M. Lara Banda, C. Gaona Tiburcio, P. Zambrano-Robledo, J.A. Cabral M, F. Estupinán L, M.A. Baltazar-Zamora, R. Croche B, E. Vera V, F. Almeraya-Calderón   +8 more
doaj   +1 more source

Strengthening mechanisms of stress rupture performance in additive-manufactured 17-4PH stainless steel

Virtual and Physical Prototyping
To obtain the desired microstructures in laser powder bed fusion 17-4PH stainless steel for multifunctional performance demands, this study optimised the microstructure and mechanical behaviour under extreme service conditions of elevated temperatures ...
Rongrong Huang, Hongyun Zhao, Yazhou Liu, Rui Ma, Yiming Sun, Jianhui Su, Danyang Lin, Bo Chen, Xiaoguo Song, Swee Leong Sing, Caiwang Tan   +10 more
doaj   +1 more source

Interlayer Tailoring of Ti-6Al-4V and 17-4PH Stainless Steel Joint by Tungsten Inert Gas Welding. [PDF]

Materials (Basel), 2023
Hajra RN, Park CW, Choi K, Kim JH.
europepmc   +1 more source

Material Properties of 17-4PH Stainless Steel Fabricated With Cooling Holes by Atomic Diffusion Additive Manufacturing (ADAM) [PDF]

, 2021
The objective of this study is to investigate the material properties of 17-4PH stainless steel printed with cooling holes in different build orientations by the Atomic Diffusion Additive manufacturing technique.
Raju, Nandhini
core  

Mass transport and porous structure evolution during solvent debinding of additively manufactured stainless steel

Virtual and Physical Prototyping
Material extrusion (ME) based additive manufacturing has gained much attention as a cost-effective method for the fabrication of complex metal components, particularly using 17-4PH stainless steel.
Yulin Liu, Audai Al-Akailah, Fuda Ning
doaj   +1 more source

Effect of TiC Content on Microstructure and Wear Performance of 17-4PH Stainless Steel Composites Manufactured by Indirect Metal 3D Printing. [PDF]

Materials (Basel), 2023
Huang X, Mei S, Li Y, Li M, Zhou S, Shang H.   +5 more
europepmc   +1 more source

Influence of intrinsic and artificial defects on the VHCF properties of 17-4PH stainless steel

Procedia Structural Integrity, 2016
AbstractIn the present work, fatigue test results in the very high cycle fatigue (VHCF) regime are discussed. Experiments were performed with smooth specimens in which crack initiation mostly originated at non-metallic inclusions. Additionally, the influence of small artificial defect, i.e. circumferential notches, drilled holes and corrosion pits, was
Schönbauer, B.M., Yanase, K., Endo, M.
openaire   +1 more source

Sintering Behavior of Bi-Material Micro-Component of 17-4PH Stainless Steel and Yttria-Stabilized Zirconia Produced by Two-Component Micro-Powder Injection Molding Process. [PDF]

Materials (Basel), 2022
Basir A, Sulong AB, Jamadon NH, Muhamad N.   +3 more
europepmc   +1 more source

Effects of Time on Microstructure and Erosion Corrosion behaviour of Liquid nitrided 17-4PH stainless steel

工程科学与技术, 2013
:Liquid nitriding of 17-4 PH martensitic precipitation hardening stainless steels was conducted at 430 °C for different time using a complex chemical heat-treatment, and the erosion corrosion resistance of the nitrided samples was evaluated. Experimental
wang jun
doaj