Results 11 to 20 of about 4,567,195 (228)
Journal of Materials Research and Technology, 2023 The current study intended to manufacture 17-4PH stainless steel using material extrusion additive manufacturing (MEAM) process and to control the microstructure and mechanical properties of the steel through heat treatment.
So-Yeon Park, Kee-Ahn Lee, Yong-Hoon Cho
exaly +5 more sources
Journal of Materials Research and Technology, 2023 The 17-4 precipitation-hardened (PH) stainless steel was prepared by laser-powder bed fusion (L-PBF), and the effects of different aging temperatures on the microstructures and properties of 17-4PH stainless steel were systematically studied. The results
Kehong Wang
exaly +4 more sources
The Effect of Aging Treatment on the Corrosion Behavior of 17-4PH Stainless Steel [PDF]
Materials (Basel)This study systematically investigated the influence of aging temperature variations on the evolution of Cu-rich precipitates and dislocation distribution characteristics in 17-4PH stainless steel through comprehensive electrochemical testing and ...
Cheng-Shuang Zhou, Yin Lv, Lin Zhang
semanticscholar +4 more sources
High cycle torsional fatigue properties of 17-4PH stainless steel [PDF]
Fracture and Structural Integrity, 2016 Sensitivity to small defects under torsional fatigue loading condition is examined in the high cycle fatigue regime. Fatigue crack initiation and small crack growth behaviors were observed during fatigue testing and fractographic investigations were ...
K. Yanase, B.M. Shönbauer, M. Endo
doaj +7 more sources
A Review of the Mechanical Properties of 17-4PH Stainless Steel Produced by Bound Powder Extrusion [PDF]
Journal of Manufacturing and Materials Processing, 2023 17-4PH Stainless Steel is a mechanically high-performing alloy that is widely used across chemical and mechanical processing industries. The alloy is conventionally fabricated by cast methods, but emerging additive manufacturing techniques are presently ...
Jaidyn Jones, Ana Vafadar, Reza Hashemi
doaj +3 more sources
Mechanical properties of 17-4PH stainless steel foam panels [PDF]
Materials Science & Engineering A: Structural Materials: Properties, Microstructure and Processing, 2007 Rectangular 17-4PH stainless steel sandwiched foam panels were fabricated using a commercial manufacturing technique by brazing two sheets to a foam core. Microstructural observations and ultrasonic nondestructive evaluation of the panels revealed large variations in the quality of the brazed areas from one panel to the next as well as within the same ...
S V Raj
exaly +4 more sources
Optimization of the 3D Printing Parameters for Tensile Properties of Specimens Produced by Fused Filament Fabrication of 17-4PH Stainless Steel [PDF]
Materials (Basel), 2020 Fused filament fabrication (FFF) combined with debinding and sintering could be an economical process for three-dimensional (3D) printing of metal parts.
D. Godec +3 more
semanticscholar +2 more sources
Effect of Layer Directions on Internal Structures and Tensile Properties of 17-4PH Stainless Steel Parts Fabricated by Fused Deposition of Metals [PDF]
Materials (Basel), 2021 17-4PH stainless steel specimens were fabricated by fused deposition of metals (FDMet) technology, which combines 17-4PH particles with an organic binder. FDMet promises a low-cost additive manufacturing process.
Y. Abe +6 more
semanticscholar +2 more sources
In Situ Characterization of 17-4PH Stainless Steel by Small-Angle Neutron Scattering. [PDF]
Materials (Basel), 2023 17-4PH martensitic steel is usually used as valve stems in nuclear power plants and it suffers from thermal aging embrittlement due to long-time service in a high-temperature and high-pressure environment. Here, we characterized the evolution of microstructures at the nano-scale in 17-4PH steel by in situ small-angle neutron scattering (SANS) with a ...
Yan S +12 more
europepmc +4 more sources
17-4PH stainless steel fastener for high salt fog open-air marine coupling. [PDF]
PLoS ONEThe C01 type diaphragm coupling demonstrates effective performance in high-concentration seawater salt fog environments. However, the fastener material for this coupling must possess high mechanical properties and strong resistance to seawater corrosion.
Angang Cao, Tao Yu, Yigui Lu, Wei Li
doaj +3 more sources