Pitting corrosion of 17-4PH stainless steel manufactured by laser beam melting [PDF]
Corrosion Science, 2020 The pitting corrosion behaviour of a 17-4PH martensitic stainless steel (MSS) manufactured by power bed laser beam melting (LBM) was compared to that of a wrought MSS. More noble pitting potentials were measured for LBM samples, probably due to a smaller size of NbCs as compared to wrought MSS.
Barroux, Adrien +4 more
openaire +6 more sources
Plasma debinding and sintering of metal injection moulded 17-4PH stainless steel [PDF]
Materials Research, 2011 In this work, 17-4PH stainless steel parts processed in a Plasma Assisted Debinding and Sintering (PADS) furnace were characterised in terms of microstructure, final density, microhardness, carbon content and tensile behaviour. To determine whether these
Renan Schroeder +3 more
doaj +1 more source
Effect of N Content on Ferrite Phase and Properties of Maraging Stainless Steel 17-4 PH [PDF]
Teshugang, 2019 The tested stainless steel 17-4PH (/% : 0.02 ~ 0. 03C, 0.40 ~ 0.50Si, 0.41 ~0. 60Mn, 0.018 ~ 0. 026P, 0. 001S, 15. 56 ~ 15.75Cr, 4. 31 ~ 4. 50Ni, 3. 21 ~ 3.40Cu, 0. 20 ~ 0.25Nb, 0. 013 〜0.
史咏鑫 +5 more
doaj +1 more source
DISSIMILAR VACUUM BRAZING OF ADDITIVE MANUFACTURED 17-4PH STAINLESS STEEL TO CONVENTIONAL 304 AND 17-4 STAINLESS STEEL BY BNI-2 BRAZING FILLER MATERIAL [PDF]
, 2023 Vacuum brazing process of 17-4PH stainless steel, which was manufactured using additive manufacturing, as well as conventional AISI304 and 17-4PH stainless steel alloys was investigated. The brazing process was conducted at 1050°C for 20 minutes under 10-
Karakaya, I. +3 more
core +2 more sources
Material Properties of 17-4PH Stainless Steel Fabricated by Atomic Diffusion Additive Manufacturing (ADAM) [PDF]
, 2021 The objective of this paper is to investigate the material properties of 17-4PH stainless steel printed by the Atomic Diffusion Additive manufacturing technique.
Kapat, Jayanta +6 more
core +2 more sources
Low cycle fatigue life improvement of AISI 304 by initial and intermittent wire brush hammering [PDF]
, 2013 The effects of hammering by wire brush as a method of improving low cycle fatigue life of highly ductile austenitic stainless steel AISI 304 have been investigated through an experimental study combining imposed strain fatigue tests and assessment of ...
KHLIFI, Ammar +4 more
core +1 more source
Electrochemical Study of Corrosion Behavior of Stellite 6 Alloy and 17-4PH Stainless Steel in Amine Solutions [PDF]
, 2017 To provide the power generation industry with scientific evidence, the corrosion behavior of Stellite 6 alloy and 17-4PH stainless steel is studied in morpholine, cyclohexylamine and sodium hydroxide solutions at the same pH around 9.5 using ...
Li, Yi
core +1 more source
Influence of hydrogen on the stress-relaxation properties of 17-4PH martensitic stainless steel manufactured by laser powder bed fusion [PDF]
, 2022 To evaluate the interactions between hydrogen and the mechanical behavior of additively manufactured (AM) 17-4PH martensitic stainless steel (MSS), stress-relaxation tests were performed for both non-charged and hydrogen-charged samples.
Blanc, Christine +5 more
core +1 more source
Effect of surface preparation on the corrosion of austenitic stainless steel 304L in high temperature steam and simulated PWR primary water [PDF]
, 2012 The corrosion behavior of 304L grade stainless steel (SS) in high-temperature steam and in a simulated Pressurized Water Reactor (PWR) is studied. The goal was to characterize the nature of the oxide coating generated during 500 h exposure of samples in ...
Cissé, Sarata +4 more
core +1 more source
Fatigue life optimization for 17-4Ph steel produced by selective laser melting [PDF]
, 2022 International audiencePurpose: The mechanical characterization of Selective Laser Melting (SLM) parts is an industrial challenge. In this paper, a methodology is proposed to control the fatigue life of 17-4Ph stainless steel by selecting the most ...
Chaves-Jacob, Julien +3 more
core +1 more source