Results 51 to 60 of about 4,567,195 (228)
Surface finish, microhardness and microstructure of laser metal deposited 17-4PH stainless steel
South African Journal of Science, 2022 Laser metal deposition is a metal-based additive manufacturing technology. It is a very sensitive and complex process because of the different process parameters involved and the interrelations between these parameters.
Abiodun Bayode
doaj +1 more source
The International Journal of Advanced Manufacturing TechnologyThis work aims at investigating the causes affecting the dimensional and geometrical accuracy of holes in metal binder jetting stainless steel parts. Parallelepiped samples with a through hole were produced using AISI 316L and 17-4PH powders, differing ...
M. Zago +3 more
semanticscholar +1 more source
, 2017 To provide the power generation industry with scientific evidence, the corrosion behavior of Stellite 6 alloy and 17-4PH stainless steel is studied in morpholine, cyclohexylamine and sodium hydroxide solutions at the same pH around 9.5 using ...
Li, Yi
core +1 more source
CoatingsThis study aims to investigate the wear and corrosion–wear behavior of 17-4PH stainless steel specimens, both fabricated via Selective Laser Melting (SLM) and conventional bulk material, after undergoing Solution Treatment (S.T.) in a seawater medium ...
Bo-Xun Hou +4 more
semanticscholar +1 more source
Advanced Engineering Materials, Volume 28, Issue 16, 19 August 2026.X‐ray computed tomography reveals how process‐induced defects evolve from green to sintered states in Fused Filament Fabrication (FFF)‐manufactured 17‐4PH stainless steel. Internal porosity, weakest cross‐sections, and fracture locations show strong correlation with tensile performance, demonstrating the potential of computed tomography (CT)‐based ...
György Ledniczky +3 more
wiley +1 more source
Exploiting Residual Elements Arising from Scrap Steel in Future Sustainable Steel Alloy Design
steel research international, Volume 97, Issue 8, Page 4270-4281, August 2026.Herein, the effects of residual elements Cu and Sn on grain growth, recrystallization, and phase transformation in C–Mn steel are summarized, and a case study is presented on how the presence of residual elements can be exploited to reduce deliberate Nb microalloying while achieving the same grain size control and strength during thermomechanical ...
Claire Davis +5 more
wiley +1 more source
An evaluation of weld metal nitrogen retention and properties in 316NL austenitic stainless steel [PDF]
, 2011 A series of tests were conducted using varying levels of nitrogen and helium in a conventional argon shielding gas when welding 316LN austenitic stainless steel. The outcome was that a 15 per cent nitrogen addition to the argon shielding gas had the most
Baker, Thomas +2 more
core +4 more sources
Corrosive-wear resistance of stainless steels for the impeller of slurry pump used in zinc hydrometallurgy process [PDF]
China Foundry, 2005 This paper presents corrosive-wear (C-W) behaviors of three kinds of steels under the simulating condition of traditional zinc hydrometallurgy process by using a self-made rotating disk apparatus.
Ping LI, Qizhou CAI, Bokang WEI
doaj
Fatigue &Fracture of Engineering Materials &Structures, Volume 49, Issue 2, Page 469-482, February 2026.ABSTRACT The advent of AM engendered unprecedented control over materials distribution, spurring interest in multi‐material fabrication. Among AM techniques, powder bed fusion—laser beam (PBF‐LB) stands out, although it requires adaptation for multi‐material printing.
Vito Errico +3 more
wiley +1 more source
Applied MechanicsThis methodology investigates the determination of the fracture toughness of 3D-printed specimens under monotonic loading conditions. The application is based on the use of a Single Edge Notch Bending (SENB) specimen made by a 3D-printing process (17-4PH
Ali Makke +3 more
doaj +1 more source