Results 141 to 150 of about 439 (171)
Some of the next articles are maybe not open access.
Effects of Laser Melting Treatment on Cavitation Erosion of 17-4PH Steel
Advanced Materials Research, 2013Cavitation erosion behavior of 17-4PH steel used for large turbine blades and laser surface melting layer were investigated in simulated seawater 3.5%NaCl solution through an ultrasonic vibration system. The microstructure and the eroded surface and cross-section morphology were observed by SEM and OM, then the results were compared and analyzed.
Song Zhang +4 more
openaire +1 more source
The Effect of Thermomechanical Treatment On Pitting Corrosion of 17-4PH Stainless Steel
ECS Meeting Abstracts, 2013Abstract not Available.
Mozhgan Abooei Mehrizi +1 more
openaire +1 more source
Experimental investigation on selective laser melting of 17-4PH stainless steel
Optics & Laser Technology, 2017Abstract Selective laser melting (SLM) is an additive manufacturing (AM) technique that uses powders to fabricate 3Dparts directly. The objective of this paper is to perform an experimental investigation of selective laser melted 17-4PH stainless steel. The investigation involved the influence of separate processing parameters on the density, defect,
Zhiheng Hu +3 more
openaire +1 more source
Effect of ECAP on the Microstructure and Mechanical Properties of 17-4PH Stainless Steel
Materials Science Forum, 2010Experiments were conducted to evaluate the influence of equal-channel angular pressing (ECAP) on the microstructure and mechanical properties of 17-4PH steel. The 17-4PH steel was solution-treated at 1040°C for 1h followed by oil cooling before ECAP process.
Gang Yang, Feng Shi Yin
openaire +1 more source
Inhibitive Effect of Nitrate on Pitting Corrosion of 17-4PH Stainless Steel
Corrosion, 2016In this work, the inhibition effect of nitrate on the pitting corrosion of 17-4PH stainless steel was investigated in the chloride solution. Potentiodynamic and potentiostatic techniques were used to measure the pitting potential and induction time in various concentrations of chloride and nitrate ions.
M. Seyedi +4 more
openaire +1 more source
Microstructure and hardness investigation of 17-4PH stainless steel by laser quenching
Materials Science and Engineering: A, 2012Abstract Surface hardening of 17-4PH was achieved by laser transformation hardening using 5 kW continuous wave CO 2 laser system. The microstructure of the laser-quenched sample was investigated by optical microscopy, transmission electron microscope and 57 Fe Mossbauer spectrometer. The hardness profile was determined by a Vickers hardness tester.
Zhaoyun Chen +2 more
openaire +1 more source
Influence of Sulfur Content on the Corrosion Resistance of 17-4PH Stainless Steel
Journal of Materials Engineering and Performance, 2017According to specification standards, the basic chemical composition of steel 17-4PH for special and critical applications is 15-17% Cr, 3.0-5.0% Ni, 3.0-5.0% Cu, 0.07% C (max) and 0.15-0.45% (Nb + Ta) (wt.%). The maximum sulfur content is 0.030%. However, as it will be shown in this work, this maximum limit for sulfur is too high for services where ...
S. S. M. Tavares +3 more
openaire +1 more source
EFFECT OF CASTING DEFECT ON MECHANICAL PROPERTIES OF 17-4PH STAINLESS STEEL
International Journal of Modern Physics B, 2006Damage and integrity evaluation techniques should be developed steadily in order to ensure the reliability and the economic efficiency of gas turbine engines. Casting defects may exist in most casting components of gas turbine engines, and the defects could give serious effect on mechanical properties and fracture toughness.
JONG-YUP KIM +2 more
openaire +1 more source
MECHANICAL PROPERTIES OF 17-4PH STEEL, HOMOGENIZED VERSUS AS RECEIVED CONDITION
1964Abstract : For the particular heat of 17-4PH steel plate involved, homogenizing treatment improved the ductility as measured by the reduction of area and reduced the spread in ductility data ,or each aged condition. (Author)
openaire +1 more source
Sintering Of A Boron-Doped İnjection Moulded 17-4ph Stanless Steel [PDF]
, 2020 Powder injection molding (PIM) is an attractive process to produce complex, near-net shaped components. The process overcomes the shape limitation of traditional powder compaction, the cost of machining, the productivity limits of isostatic pressing and slip casting, and the defect and tolerance limitations of conventional casting.
Sakarya Uygulamalı Bilimler Üniversitesi/Teknoloji Fakültesi/Metalurji Ve Malzeme Mühendisliği Bölümü +2 more
openaire