Results 41 to 50 of about 287 (172)

Transformation Characteristics and Properties of B Steel 22MnB5

Materials Today: Proceedings, 2015
Abstract Continuous cooling transformation characteristics of steel 22MnB5 were studied in detail using dilatometer method. The influence of hot forming procedure parameters, such as heating rate, austenizing temperature, and holding time on microstructure transition was analyzed. Microhardness was tested afterwards.
Zhang, M., Wan, Z., Li, L.
openaire   +1 more source

Press Hardening for Sustainable Lightweight Chassis Design in Heavy‐Duty Vehicles: A Material Performance and Life Cycle Assessment Approach

steel research international, EarlyView.
The article explores how high‐strength steels and press hardening revolutionize lightweight chassis design for heavy‐duty vehicles. It reveals that press hardened steels combined with shot peening can cut weight by up to 34% and reduce environmental impact by 21%–32%.
Violeta Vargas‐Parra, Sergi Parareda, Jose Jorge Espí‐Gallart, Jaume Pujante, Gustaf Gustafsson, Henrik Sieurin, David Frómeta, Daniel Casellas   +7 more
wiley   +1 more source

Influence of Chemical Composition and Microstructural Transformation of Two Low-Carbon Steels on Fine Blanking and Further Carbonitriding Heat Treatment

Metals
The effect of the chemical composition of two low-carbon steels, C18E and 22MnB5, on their behavior after forming by fine blanking was investigated. A specific tool, adaptable to a tensile testing machine, was designed to replicate an industrial half ...
Thomas Chiavazza, Margaux Marnier, Aurélie Achille, Sophie Eve, Eric Hug   +4 more
doaj   +1 more source

Effect of initial blank temperature in hot press forming towards 22MnB5 springback failure

Journal of Mechanical Engineering and Sciences, 2019
The springback failure of ultra-high strength boron steel (22MnB5) in hot press forming (HPF) process was characterized under bending and membrane conditions.
C. H. Ng, C. F. Lai, S. N. M. Yahaya, S. Shamsudin, S. N. A. S. Ahmad, F. Sharrifuddin   +5 more
doaj   +1 more source

Numerical and Experimental Analysis of Hardening Distortions of Drawpieces Produced in Hot Stamping Process

Metals, 2021
The paper presents the results of a numerical simulation of the distortions in drawpieces, generated during the production of the drawpieces using the hot stamping method.
Ireneusz Wróbel
doaj   +1 more source

Insights Into Paint‐Bake Toughening of Resistance Spot Welds of a 2.0 GPa Warm‐Stamped Medium‐Mn Steel

steel research international, EarlyView.
Paint baking of resistance spot welded joints of 2.0 GPa warm‐stamped medium‐Mn steel activates low‐temperature tempering, forming fine cementite in the fusion zone and enhancing toughness. Crack propagation resistance increases, shifting the failure mode from partial interfacial to complete pullout, with peak load and energy absorption rising ...
Sunusi Marwana Manladan, Savyasachi Nellikode, YeoJin Jang, Sumin Lee, Dileep Chandran Ramachandran, Sung‐bo Heo, Jinyoung Lee, Young‐Kook Lee, Yeong‐Do Park   +8 more
wiley   +1 more source

Phase transformation temperatures and Fe enrichment of a 22MnB5 Zn-Fe coated steel under hot stamping conditions

Journal of Materials Research and Technology, 2020
In the last years, press-hardening steels have contributed to the automotive industry successfully to meet the increasing regulations for reducing fuel consumption and stringent greenhouse gas emissions while improving passenger safety by manufacturing ...
Daniel Alexandre da Costa Ximenes, Luciano Pessanha Moreira, José Eduardo Ribeiro de Carvalho, Duílio Norberto Ferronatto Leite, Reginaldo Gomes Toledo, Fabio Moreira da Silva Dias   +5 more
doaj   +1 more source

Resistance Rapid Heating of Aluminum Coatings in an Extreme High Vacuum–Adequate Atmosphere for Hot Stamping

Advanced Engineering Materials, Volume 28, Issue 12, 17 June 2026.
The subject of this work is the development of a corrosion‐protective coating on steel sheets for form hardening. Rapid heating in an extreme high vacuum (XHV)‐adequate atmosphere is a useful method to prevent oxidation during alloying of 22MnB5 and aluminum to obtain a metallurgical bonding.
Lorenz Albracht, Alexander Schnettger, Ulrich Holländer, Sven Hübner, Bernd‐Arno Behrens, Hans Jürgen Maier   +5 more
wiley   +1 more source

High Temperature Friction and Wear Performance of PVD Coatings under Press Hardening Contact Conditions

Advances in Tribology, Volume 2019, Issue 1, 2019., 2019
Press hardening is widely employed to produce automotive structural and safety components from advanced high‐strength steels. This process depends on friction between the forming tools and the work piece. Wear of the forming tools affects the dimensional accuracy of produced components and reduces their service life. It is therefore desirable to reduce
Sergej Mozgovoy, Jens Hardell, Braham Prakash, Huseyin Çimenoǧlu   +3 more
wiley   +1 more source

Study on Microstructure and Properties of a New Warm-Stamped Niobium-Alloyed Steel

Metals, 2019
The warm stamping technology is a promising technology to meet the needs of car weight reduction and energy conservation. In order to compare with the mechanical properties of the traditional hot-stamped boron-alloyed steel 22MnB5, a new warm-stamped ...
Peng Tian, Wen Liang, Zhennan Cui, Guoming Zhu, Yonglin Kang, Baoshun Li, Li Lin, Rendong Liu   +7 more
doaj   +1 more source