Results 131 to 140 of about 179,536 (231)

In Situ Micromechanical Study of Bimodal γ′–γ″ Precipitate Assemblies in Ni–Cr–Al–Nb Superalloy

Advanced Engineering Materials, EarlyView.
A Ni–Cr–Al–Nb superalloy with a bimodal γ′–γ″ precipitate distribution is developed. Composite precipitate assemblies form through heterogeneous nucleation, effectively impeding dislocation motion. Micropillar compression reveals high strength at room and elevated temperatures, governed by precipitate shearing, with coupled faulting mechanisms ...
Ujjval Bansal, Tae‐Hyeok Kang, Pyuck‐Pa Choi, Subin Lee, Christoph Kirchlechner   +4 more
wiley   +1 more source

Assessing the structural performance of additively manufactured carbon fibre reinforced PLA-based adherends bonded with graphene-enhanced adhesive using experimental and ANN analysis. [PDF]

Sci Rep
Dhilipkumar T, Karthikeyan N, Murali AP, Shankar KV, Karuppusamy P, Fatehmulla A, Kumar R, Selvakumar K.   +7 more
europepmc   +1 more source

Electrochemical Behavior of Flame‐Sprayed Sc‐Doped AlCoCrFeMo High‐Entropy Alloy Coatings in 3.5% Sodium Chloride Solution

Advanced Engineering Materials, EarlyView.
Scandium (Sc)‐doped AlCoCrFeMo HEA coatings are fabricated via flame spraying with 0.1, 0.3, and 0.5 wt% Sc additions. Among these, the HEA‐Sc0.3 coating exhibits the highest corrosion resistance, indicated by a more positive corrosion potential and lower current density.
Pankaj Kumar, Akash Vyas, Mohammad Aatif Qazi, Nashit Jalal, Maria Ophelia Jarligo, Mostafa Yakout, Jing Liu, André McDonald   +7 more
wiley   +1 more source

Repair Performance of Additively and Subtractively Manufactured Permanent Crown Materials: A Combined Mechanical and Optical Evaluation. [PDF]

Materials (Basel)
Karagözoğlu İ, Parlar Öz Ö, Demirkol N, Eyüboğlu TF, Özcan M.   +4 more
europepmc   +1 more source

Encyclopedia of 2D β′‐In2Se3 Growth Using Chemical Vapor Deposition: The Effects of Synthesis Parameters Onto Material Quality

Advanced Engineering Materials, EarlyView.
A distinct semi‐confined inner‐tube chemical vapor deposition geometry enables reproducible, large‐area growth of phase‐pure 2D β′‐In2Se3 from InI + Se precursors. Engineering local vapor transport and optimizing precursor delivery and temperature–time conditions yield uniform continuous films.
Dasun P. W. Guruge, P. Sanju S. Panawala, Joseph F. S. Fernando, Zhenhuan Chen, Chao Zhang, Dong‐Chen Qi, Liangzhi Kou, Konstantin L. Firestein, Dmitri V. Golberg   +8 more
wiley   +1 more source

Liquid Deposition Modeling of Biobased Epoxy Composites: Natural Fillers as Rheology Modifiers and Reinforcements. [PDF]

ACS Omega
Albertini E, Fragkogiannis C, Tsantilis L, Arrigo R, Vitale A, Bongiovanni R, Dalle Vacche S.   +6 more
europepmc   +1 more source

Low Cycle Repetitive Loading of Ti‐6Al‐4V‐Epoxy Composite Lattice Structures for Enhanced Energy Dissipation and Damage Tolerance

Advanced Engineering Materials, EarlyView.
Composite Ti–6Al–4V–epoxy lattice structures are additively manufactured and epoxy infiltrated for cyclic loading. At low lattice volume fractions, hybridization produces synergistic gains in stiffness and energy dissipation. At higher volume fractions, synergy diminishes, although composites still exceed metallic lattices in specific energy ...
Joey Tallon, Jordan Noronha, Justin Dirrenberger, Andrey Molotnikov   +3 more
wiley   +1 more source

Rapid modeling of 3D rice canopy structure considering vertical heterogeneity and analysis of spectral response. [PDF]

Plant Phenomics
Bai J, Tian Y, Hui Y, Wu R, Yu F, Wang C.   +5 more
europepmc   +1 more source

Enhancing Bubble Removal in Geometry‐Optimized Electrodes

Advanced Engineering Materials, EarlyView.
3D‐printed lattice electrodes outperform stochastic foams in alkaline water electrolysis despite 20%–25% lower surface area. Straight flow channels generate Venturi‐like bubble entrainment, suppressing gas accumulation that renders foam interiors electrochemically inactive.
Florian Wiesner, Peter Förster, Alexander Limper, Anselm Brodersen, Matthias Wessling, John Linkhorst   +5 more
wiley   +1 more source

Effect of denture tooth manufacturing and adhesive materials on bond strength of 3D-printed denture base. [PDF]

J Clin Exp Dent
Saengthongpinij T, Apinsathanon P, Mahardawi B, Laoharungpisit P, Nan PN, Aimjirakul N.   +5 more
europepmc   +1 more source