Results 151 to 160 of about 33,336 (259)

Monitoring Nystagmus in a Patient With Vertigo Using a Commercial Mini-Infrared Camera and 3D Printer: Cost-Effectiveness Evaluation and Case Report. [PDF]

JMIR Form Res
Sakazaki H, Noda M, Dobashi Y, Kuroda T, Tsunoda R, Fushiki H.   +5 more
europepmc   +1 more source

3D printer design

Treball desenvolupat en el marc del programa "European Project Semester".
Omodolor Omodia, Ikechukwu Danromy, Livingstone, Benjamin, Foissard, Etienne   +2 more
openaire   +1 more source

Transient Charging of Mixed Ionic‐Electronic Conductors by Anomalous Diffusion

Advanced Materials, EarlyView.
This article explores charge transport in mixed ionic‐electronic conductors (MIECs) through electrochemical impedance spectroscopy and transient current analysis. Focusing on PEDOT:PSS, WO3, and n‐doped PBDF, it uncovers the impact of anomalous diffusion via fractional modeling. The study reveals key correlations that deepen understanding and guide the
Heyi Zhang, Gonzalo Rivera‐Sierra, Shirin Siahjani‐Gultekin, Jenifer Rubio‐Magnieto, Anis Allagui, Ignacio Sanjuán, David Franco, Antonio Guerrero, Enrique H. Balaguera, Juan Bisquert   +9 more
wiley   +1 more source

Letter to the editor regarding "Promotion of bone-tendon healing after ACL reconstruction using scaffold-free constructs comprising ADSCs produced by a bio-3D printer in rabbit models". [PDF]

J Orthop Translat
Du Y.
europepmc   +1 more source

Opportunities of Semiconducting Oxide Nanostructures as Advanced Luminescent Materials in Photonics

Advanced Materials, EarlyView.
The review discusses the challenges of wide and ultrawide bandgap semiconducting oxides as a suitable material platform for photonics. They offer great versatility in terms of tuning microstructure, native defects, doping, anisotropy, and micro‐ and nano‐structuring. The review focuses on their light emission, light‐confinement in optical cavities, and
Ana Cremades, Pedro Hidalgo, David Maestre, Ruth Martínez‐Casado, Emilio Nogales, Beatriz Rodríguez, G. Cristian Vásquez, Bianchi Méndez   +7 more
wiley   +1 more source

Using a Model Created Using a 3D Printer to Mould a Grey Cast Iron Casting. [PDF]

Materials (Basel)
Ráž K, Chval Z, Kořínek J.
europepmc   +1 more source

Self‐Assembled Inorganic Nanomembrane Tubes: Rolled‐Up Piezoelectrics for Microacoustic Wave‐Based Actuators and Sensors

Advanced Materials, EarlyView.
This study demonstrates a self‐assembly process to generate free‐standing piezoelectric nanomembranes, forming ultracompact microtubular acoustic wave sensors and actuators. The miniaturized 3D piezoelectric platform reported in this work can be applied in telecommunication, energy harvesting, and acoustofluidics. Moreover, the 3D self‐assembly can add
Raphaël C. L‐M. Doineau, Christian N. Saggau, Stefan Baunack, Thomas Gemming, Yara Abdelaal, Robert Weser, Oliver G. Schmidt, Hagen Schmidt, Andreas Winkler, Mariana Medina‐Sánchez   +9 more
wiley   +1 more source

Adaptive Fabrication of Electrochemical Chips with a Paste-Dispensing 3D Printer. [PDF]

Sensors (Basel)
Wong TI, Ng C, Lin S, Chen Z, Zhou X.
europepmc   +1 more source

Electrically Readable Lateral Flow Assay Using Organic Transistors for Diagnostic Applications

Advanced Materials, EarlyView.
Electrolyte‐gated organic field‐effect transistors (EGOFETs) are integrated with lateral flow (LF) paper fluidics to create a reusable, portable, and low‐cost point‐of‐care (PoC) diagnostic test. The devices are validated for Human Immunoglobulin G detection, achieving high sensitivity (0.1 fm), selectivity, and reproducibility with rapid results in 20–
María Jesús Ortiz‐Aguayo, Carme Martínez‐Domingo, Diego Gutiérrez, Dean Kos, Marta Mas‐Torrent   +4 more
wiley   +1 more source

EnderScope: a low-cost 3D printer-based scanning microscope for microplastic detection. [PDF]

Philos Trans A Math Phys Eng Sci
Burke N, Müller G, Saggiomo V, Hassett AR, Mutterer J, Ó Súilleabháin P, Zakharov D, Healy D, Reynaud EG, Pickering M.   +9 more
europepmc   +1 more source