Results 131 to 140 of about 3,610,239 (308)
Mechanical properties of modified low cobalt powder metallurgy Udimet 700 type alloys [PDF]
Eight superalloys derived from Udimet 700 were prepared by powder metallurgy, hot isostatically pressed, heat treated and their tensile and creep rupture properties determined.
Harf, Fredric H.
core +1 more source
Advanced Engineering Materials, EarlyView.This study investigates how tramp elements from increased scrap usage influence phase transformations in low‐alloyed steel. Combining dilatometry and microscopy reveal that tramp elements delay transformations, reduce critical cooling rates and increase hardenability.
Lukas Hatzenbichler +5 more
wiley +1 more source
Multimodal Data‐Driven Microstructure Characterization
Advanced Engineering Materials, EarlyView.A self‐consistent autonomous workflow for EBSP‐based microstructure segmentation by integrating PCA, GMM clustering, and cNMF with information‐theoretic parameter selection, requiring no user input. An optimal ROI size related to characteristic grain size is identified.
Qi Zhang +4 more
wiley +1 more source
Essential Entry: Revenues in the 700 MHz Spectrum Auction [PDF]
A common misconception is that an open access provision on a sliver of the 700 MHz spectrum would reduce auction revenues. In fact, the open access, wholesale, and bidding credit provisions put forth by Frontline Wireless, will motivate new entry ...
Peter Cramton
core
Microstructure Evolution of a VMnFeCoNi High‐Entropy Alloy After Synthesis, Swaging, and Annealing
Advanced Engineering Materials, EarlyView.The synthesis and processing (rotary swaging and annealing) of the novel VMnFeCoNi alloy is investigated, alongside the estimation of the grain size effect on hardness. Analysis of a wide grain size range of recrystallized microstructures (12–210 µm) reveals a low annealing twin density.
Aditya Srinivasan Tirunilai +6 more
wiley +1 more source
Clinical OphthalmologySam Multack,1 Nellie Plummer,1 Athanasios Marneris,1 Brad Hall2 1Multack Eye Care, Frankfort, IL, USA; 2Sengi, Penniac, NB, CanadaCorrespondence: Sam Multack, Multack Eye Care, 22200 Wolf Road, Frankfort, IL, 60423, USA, Tel +1-815-889-3333, Email ...
Multack S, Plummer N, Marneris A, Hall B
doaj
Creep Properties and Deformation Mechanism of Additively Manufactured NiAl‐CrMo Composites
Advanced Engineering Materials, EarlyView.Additively manufactured NiAl‐CrMo composites contain numerous interfaces and cell boundaries that control their creep response. At 700°C under high applied stress, creep is dominated by dislocation‐controlled power‐law mechanisms. At 800°C–900°C and lower stresses, creep is primarily diffusion‐controlled along cell boundaries.
Jan Vollhüter +9 more
wiley +1 more source
Enhanced Strength and Corrosion Resistance of Ti‐13Nb‐12Ta‐10Zr‐4Sn Alloy by Aging Treatment
Advanced Engineering Materials, EarlyView.This work systematically investigates the effect of aging treatment on mechanical properties and corrosion behavior of vacuum arc‐melted Ti‐13Nb‐12Ta‐10Zr‐4Sn alloy. Owing to the increased α″ martensite, strength and corrosion resistance were significantly enhanced by aging treatment.
Yuhua Li +5 more
wiley +1 more source
THREE APPLICATIONS OF TRANSACTION COST ECONOMICS IN ROMANIA [PDF]
International Monetary Fund Institute, 700 19th Street, N.W,.Washington, D.C.
Radu A. Păun
core
Advanced Engineering Materials, EarlyView.This plot compares experimental tensile stress–strain curves (with 4 different strain rates) and corresponding modelled curves (obtained using the optimised sets of Voce and Miller–Norton parameter values shown). The inferred M‐N values, characterizing the creep, are very similar to those obtained via conventional creep testing.
S. Ooi, R. P. Thompson, T. W. Clyne
wiley +1 more source