Results 31 to 40 of about 5,355 (145)

Slip Localization Intensification Mediated by Grain Boundary Sliding in a Polycrystalline Nickel‐Based Superalloy

Advanced Engineering Materials, EarlyView.
The temperature dependence of fatigue behavior in nickel‐based superalloys is investigated through high‐resolution measurements of plastic localization. While increasing temperature reduces localization and enhances fatigue performance in René 88DT, Inconel 718 exhibits a sharp degradation at intermediate temperature due to intensified slip ...
M. Calvat, D. Anjaria, I. Woo, C. Bean, D. Texier, J. C. Stinville   +5 more
wiley   +1 more source

Creep‐Induced Microstructural Evolution in an A2‐B2 Superalloy

Advanced Engineering Materials, EarlyView.
A 27.3Ta‐27.3Mo‐27.3Ti‐8Cr‐10Al (at.%) refractory high‐entropy alloy with precipitation‐strengthened A2‐B2 microstructure was studied by creep tests at 1030°C, which demonstrate a transition in deformation mechanisms in the range of 100–150 MPa applied stress. This is associated with changes in dislocation–precipitate interactions. Relevant deformation
Liu Yang, Aparajita Pramanik, Sandipan Sen, Shubhashis Dixit, Marcel Muench, R. J. Vikram, Daniel Schliephake, Yolita M. Eggeler, Ankur Chauhan, Martin Heilmaier, Alexander Kauffmann   +10 more
wiley   +1 more source

Lesiones no cariosas del cuello dentario:

Odontoestomatología, 2019
Las lesiones no cariosas del cuello dentario (LCNC) son consideradas defectos frecuentes caracterizados por una marcha insidiosa y una etiología controversial.
Hugo Calabria Díaz
doaj   +2 more sources

Influence of Test Temperature and Test Frequency on Fatigue Life of Aluminum Alloy EN AW‐2618A

Advanced Engineering Materials, EarlyView.
The influence of test temperature and test frequency on the fatigue life of EN AW‐2618A is investigated. High‐cycle fatigue tests are performed at different test temperatures and frequencies on the 1000 h/230°C overaged state. Both test parameters reduce fatigue life due to time‐dependent damage mechanisms.
Ying Han, Julian M. Rosalie, Jan Radners, Mauro Madia, Philipp von Hartrott, Birgit Skrotzki   +5 more
wiley   +1 more source

Sustainable aggregate impact on pervious concrete abrasion resistance

Results in Engineering, 2023
Pervious concrete, known for its high porosity and permeability, is commonly used for low-traffic pavements. This study investigates the impact of sustainable aggregates on abrasion resistance in pervious concrete, specifically electric furnace slag (EFS)
Gersson F.B. Sandoval, Ricardo Pieralisi
doaj   +1 more source

Recycling of NiTi Shape Memory Alloys: Fundamental and Technological Aspects of a Vacuum Induction Melting Processing Route

Advanced Engineering Materials, EarlyView.
The present study investigates recycling of NiTi shape memory alloys via vacuum induction melting. An ingot was synthesized from elemental Ni and Ti and subjected to three subsequent remelting cycles. Remelting increases process durations and impurity levels and adversely affects microstructures and functional properties.
Sakia Sophia Noorzayee, Son Tung Mai, Sarath Menon, Braulio Gadiel Sánchez Ortega, Ralf Drautz, Alexander Kauffmann, Gunther Eggeler, Jan Frenzel   +7 more
wiley   +1 more source

Lesiones dentales no cariosas en pacientes atendidos en la Clínica Estomatológica Siboney

Revista Cubana de Investigaciones Biomédicas, 2019
Introducción: El desgaste dental es un proceso insidioso y acumulativo que lleva a la destrucción del esmalte y la dentina; conocido como lesiones dentales no cariosas y son: Atrición, Abrasión, Abfracción y Erosión.
Héctor Juan Ruiz Candina, Aleida Josefa Herrera Batista, Javier Gamboa Sosa   +2 more
doaj  

Current Status and Challenges in Data Collection for Aerospace Coatings Deposited by Plasma Spraying

Advanced Engineering Materials, EarlyView.
An innovative approach has been integrated into the GRENAT project to optimize plasma spraying and coating performance. Raw materials are accelerated and melted in the plasma generated by torches, creating coatings. Monitoring sensors collect process data which are combined with ex situ characterization data.
Lila Randriamananjara, Vincent Rat, Quentin Dubreuil, Patrice Valorge, Simon Goutier, Alain Denoirjean, Olivier Messe, Céline Ruelle, Jean‐Philippe Poli   +8 more
wiley   +1 more source

Optimization of the Production of Rubber Compounds Using Mathematical Models

Advanced Engineering Materials, EarlyView.
Rubber compounds were mixed in a batch internal mixer, and symbolic regression was used to derive mathematical models linking recipe and process parameters to ram path, torque, and mixing quality (incorporation, dispersion, distribution). Subsequent optimization with evolutionary algorithms identified operating conditions that reduce specific energy ...
Anke Bardehle, Andreas Limper, Ulrich Giese, Carlos Lucke, Mario Beiner, Christoph Gögelein, Lisa Leuchtenberger‐Engel, Christian Hopmann   +7 more
wiley   +1 more source

Changes in the properties of white cast iron ичx2h4 under conditions of variations of heating

Minería y Geología, 2016
The influence of three heating variants, during hardening on the properties of national manufactured ИЧX2H4 white cast iron were evaluated at laboratory scale in order to predict the feasibility of using it on the manufacturing of mining equipments for ...
Tomás Fernández-Columbié, Gleydis Dueñas- Rodríguez, Armín Mariño-Pérez, Alberto Velázquez-del Rosario, Dayanis Alcántara-Borges   +4 more
doaj