Results 111 to 120 of about 49,247 (265)

Feasibility of Nitrogen as a Carrier Gas for Inconel Cold Spray in Hydropower Application

Advanced Engineering Materials, EarlyView.
N2, despite being nearly two orders of magnitude cheaper than He, is a feasible carrier gas for cold spray Inconel coatings in hydropower repair applications when higher gas temperature and pressure are used. Reducing powder size significantly improved cavitation resistance, while the addition of fine chromium carbide particles further enhanced erosion
Tianhao Wang, Mayur Pole, Tingkun Liu, Kenneth A. Ross, Christopher B. Smith   +4 more
wiley   +1 more source

Electrical and mechanical properties of conductive elastic bands as wearable sensors. [PDF]

Sci Rep
Mustafa E, Naeem M, Badr AA, Abdel-Magied ZM, Mohamed AA.   +4 more
europepmc   +1 more source

Influence of Si Content and Milling Duration on the Microstructure and Mechanical–Tribological Properties of AlCoCrFeNiSi High‐Entropy Alloys

Advanced Engineering Materials, EarlyView.
Si‐doped AlCoCrFeNi high‐entropy alloys are synthesized by mechanical alloying to reveal the effect of Si content and milling time on phase evolution, microstructural refinement, and tribological behavior. A transition from FCC to BCC structure, significant grain refinement, and enhanced hardness and wear resistance are achieved, with the 4 at% Si ...
Mustafa Okumuş, Mehmet Emin Demir, Sercan Özpınar   +2 more
wiley   +1 more source

Effects of cold temperatures on abrasion resistance of concrete with different mixture compositions. [PDF]

Sci Rep
Ismail MK, Hassan AAA, Shehata OE.
europepmc   +1 more source

Abrasion [PDF]

, 2020
openaire   +1 more source

Microstructure, Thermal Transport, and Dry‐Sliding Tribology of Powder‐Metallurgy Al7075 Composites Reinforced With Sol–Gel‐Derived ZnO–rGO Hybrid Nanoparticles

Advanced Engineering Materials, EarlyView.
Sol–gel‐derived ZnO–rGO hybrid nanoparticles enable Al7075 powder‐metallurgy composites to achieve concurrent gains in hardness and thermal conductivity while markedly lowering friction and wear. The hybrid architecture couples ZnO‐based load support with rGO‐assisted lamellar sliding and heat spreading, revealing a promising route toward lightweight ...
Bunyamin Aksakal, Cevher Kursat Macit, Merve Ayık, Hakan Tutumlu   +3 more
wiley   +1 more source

Electrical properties and surface roughness of carbon fibre reinforced polymer under progressive surface abrasion. [PDF]

Data Brief
Osama M, Jones CE, Stephen B.
europepmc   +1 more source

Electrified Damage in Motion Systems

Advanced Engineering Materials, EarlyView.
The electrified damage in motion systems is a fundamental framework presenting the degradation pathway arising from the coupling of electrical energy transport with mechanical contact and interfacial chemistry. The framework positions electrified damage as a distinct degradation regime with unique characteristic surface morphologies and failures of ...
M. Humaun Kabir, Angelina Nguyen, Hong Liang   +2 more
wiley   +1 more source

Active Corrosion Protection of Sintered AA7075 Aluminum Alloy via Mn Powder Addition

Advanced Engineering Materials, EarlyView.
AA7075 containing Mn‐rich particles is fabricated via spark plasma sintering using AA7075 and Mn powders. Corrosion resistance is evaluated through dip‐and‐dry tests using 0.1 M NaCl (pH 6.0), and mass loss decreases with increasing Mn addition. Mn‐rich particles function as a source of Mn ions, and formation of Mn‐accumulation films on Cu‐containing ...
Ko Ebina, Masashi Nishimoto, Izumi Muto
wiley   +1 more source

Analyzing the Influence of Sizing Machine Settings on the Performance of the Sized Cotton Warp Yarns Using Eco-Friendly Carboxymethyl Cellulose from Saudi Wheat Straw. [PDF]

Polymers (Basel)
Maatoug S, Abu Nab E.
europepmc   +1 more source