Results 11 to 20 of about 158,097 (358)
Journal of Materials Research and Technology, 2023 In this study, scanning electron microscopy (SEM), electron backscatter diffraction analysis (EBSD), and electron probe microanalysis (EPMA) were used to investigate the impact of rare-earth Sc on the interface microstructure and mechanical properties of
Po Zhang +9 more
doaj +1 more source
Formation of Fiber Fragments during Abrasion of Polyester Textiles.
Environmental Science and Technology, 2021 Fiber fragments are one of the dominant types of microplastics in environmental samples, suggesting that synthetic textiles are a potential source of microplastics to the environment.
Yaping Cai +3 more
semanticscholar +1 more source
Science of the Total Environment, 2022 Microplastic fibers (MPFs) released from synthetic textiles have been found to be a major source of microplastic in the environment. There is increasing evidence available that MPFs released during washing were likely formed during the manufacturing ...
Tong Yang, M. Gao, B. Nowack
semanticscholar +1 more source
Metals, 2022 Cu-W composite powder with various W contents (0, 10, 20, and 30 wt%) has been fabricated by spray drying, calcination, and two-stage hydrogen reduction in this work. The microstructures and phase evolution of Cu-W composite powder were studied by FESEM,
Qi Wang +5 more
doaj +1 more source
Optimizing of particle accelerated rotor parameters using the discrete element method
Scientific Reports, 2023 The acceleration capability of a centrifugal jet rotor plays a crucial role in achieving a high injection velocity of powder particles in the centrifugal impact moulding process.
Bo Sun +4 more
doaj +1 more source
Breakdown and Modification of Microplastic Beads by Aeolian Abrasion
Environmental Science and Technology, 2022 Saltation is an important wind erosion process that can cause the modification and breakdown of particles by aeolian abrasion. It is recognized that microplastic particles can be transported by wind, but the effect of saltation on microplastic properties
J. Bullard +3 more
semanticscholar +1 more source
Silicon, 2021 The main objective of the current research work is to explore the effect of nanosilica particles on the compound EPDM/SBR-SiO2 (ethylene-propylene-diene monomer/styrene-butadiene rubber-nanosilica). The composite EPDM/SBR with and without silane coupling
S. Vishvanathperumal, A. G
semanticscholar +1 more source
Journal of Engineered Fibers and Fabrics, 2021 As a high-performance fiber, high modulus polyethylene fiber (HMPE) has been widely used in the rope industry. However, due to its low melting point and poor thermal conductivity, it tends to break under the conditions of repeated yarn on yarn abrasion ...
Fanggang Ning +6 more
semanticscholar +1 more source
Mechanical properties and corrosion behavior in molten zinc of Mo–ZrO2 alloys
Journal of Materials Research and Technology, 2023 The effect of the ZrO2 doping amounts on the corrosion properties and mechanical properties of the molybdenum alloys in molten zinc was investigated. Among them, the Mo-1.5 wt% ZrO2 alloy has good corrosion resistance (at 460 °C) and excellent mechanical
Bin Wang +6 more
doaj +1 more source
Microstructure and abrasive wear properties of high-vanadium-chromium wear resistant alloy
Materials Research Express, 2021 To enhance the wear resistance of high chromium cast iron (HCCI, Cr26), a new wear resistant alloy with high vanadium and chromium contents (HCCI-V, 15Cr5V4MoSiMn) was designed and prepared by sand mold casting.
Fangfang Wang +4 more
doaj +1 more source