Results 41 to 50 of about 62,159 (212)
Applied Sciences, 2018 Precise processing for complex geometric surfaces of titanium alloy artificial joints has higher technical difficulties. This paper addresses the matter by proposing an improved abrasive flow processing method.
Li Zhang +3 more
doaj +1 more source
Study on high quality surface finishing technology of pre-spinning nozzle in additive manufacturing
Xibei Gongye Daxue Xuebao, 2021 Through the simulation of abrasive flow in the inner cavity of the superalloy pre-spinning nozzle made by additive manufacturing, the special abrasive polishing tool is optimized and the surface polishing technology of the inner cavity of typical ...
doaj +1 more source
Effect of Gr Contents on Wear Properties of Al2024/MgO/Al2O3/Gr Hybrid Composites [PDF]
, 2018 In the present study, hybrid metal matrix composites, Al2024/10Al2O3, Al2024/10Al2O3/3MgO, Al2024/10Al2O3/6MgO, Al2024/10Al2O3/3MgO/1.5 Gr, Al2024/10Al2O3/3MgO/3Gr, and reinforcement samples (AA 2024) produced with powder metallurgy process.
Albayrak, S. +3 more
core +1 more source
Study on whole factorial experiment of polishing the micro-hole in non-linear tubes by abrasive flow
Advances in Mechanical Engineering, 2018 It is generally observed that special channels exit in many key components of machine, such as non-linear tube, applied in military or civil industries. Its surface finish is a crucial factor in the whole performance of machine.
Guosong Liu +4 more
doaj +1 more source
Analysis on mechanism of material removal rate and surface flow machining process [PDF]
MATEC Web of ConferencesA novel finishing technique called abrasive flow machining (AFM) uses abrasive particles as the instrument for material removal. The term "self-deformable stone" refers to the abrasive particle-containing carrier medium, and AFM is commonly known as "no ...
Kondala Rao Peram, Ranga Janardhana G.
doaj +1 more source
Manufacturing Review, 2022 From last two decades, plant fiber reinforced polymer/polyester composites have been effectively used in structural and automotive applications. Researchers and manufacturers are looking forward for an effective utilization of these composites.
Shetty Raviraj, Hegde Adithya
doaj +1 more source
Energy Conversion in the Working Nozzle of a Pneumatic Abrasive-Jet Unit
Журнал інженерних наукThe article investigates the working processes in the channels with relatively simple geometry, such as working nozzles and seals designed to regulate the working flow jet passing through them.
Vadym Baha, Ján Piteľ
doaj +1 more source
The application of polymers as abrasive media in abrasive flow machining
Mechanik, 2019 The characteristics of the products’ treatment by the abrasive flow machining (AFM) makes it an appropriate method of finishing the surface with complex geometry, e.g. holes or channels. Traditional methods of machining cause difficulties in obtaining a homogeneous roughness during finishing complicated shapes due to uneven distribution of abrasive ...
Agnieszka Nowacka, Tomasz Klepka
openaire +2 more sources
Ultra-fast X-ray particle velocimetry measurements within an abrasive water jet [PDF]
, 2018 Ultra-fast X-ray velocimetry measurements were taken to measure velocities and spatial positions of individual abrasive particles within the solid-liquid-gaseous three-phase flow of a high-pressure injection method-based abrasive water jet (AWJ).
Balz, R. +4 more
core
Frontiers in Materials, 2022 In order to realize the uniform distribution in the abrasive flow polishing of the titanium alloy workpiece with curved surface, a novel method based on the liquid metal-abrasive flow machining technology is proposed in this study.
Li Zhang +11 more
doaj +1 more source