Results 61 to 70 of about 59,827 (307)

Duplex Stainless Steel Laser‐Surface Textured: Stability in Brine Solution

Advanced Engineering Materials, EarlyView.
Controlled laser‐surface treatment (LST) of duplex DSS2205 steel is performed to increase its stability in brine solution under cyclic electrochemical assays. The superior protection with respect to flat and smooth panels is attributed to the presence of FeCr2O4 as the main protective oxide layer in the LST surface, after corrosion tests. The stability
Mohammad Rezayat, Hamidreza Enshaei, Elaine Armelin, José I. Iribarren, Antonio Mateo, Miguel Morales   +5 more
wiley   +1 more source

Electricity from photovoltaic solar cells: Flat-Plate Solar Array Project final Report. Volume III: Silicon sheet: wafers and ribbons [PDF]

, 1986
The Flat-Plate Solar Array (FSA) Project, funded by the U.S. Government and managed by the Jet Propulsion Laboratory, was formed in 1975 to develop the module/array technology needed to attain widespread terrestrial use of photovoltaics by 1985.
Briglio, A., Dumas, K., Leipold, M., Morrison, A.   +3 more
core  

PBF‐LB/M of Ti‐6Al‐4V: High‐Pressure Solution Treatment and Aging for Applications in a Sustainable Aerospace

Advanced Engineering Materials, EarlyView.
Additive manufacturing (AM) allows great geometric freedom for lightweight components. As parts are progressively optimized exploiting potentials in AM leading in smaller material cross sections, high pressure solution treating and aging (STA) treatments show an enormous potential for strongly improving material properties.
Mika León Altmann, Andre Danzig, Freerk Syassen, Rainer Fechte‐Heinen, Anastasiya Toenjes   +4 more
wiley   +1 more source

Investigation of Laser Ablation and Brush Pre‐Treatments for AlCu Cold Roll Bonding in Oxygen‐Free Conditions

Advanced Engineering Materials, EarlyView.
It is shown that laser ablation pretreatment under oxygen‐free conditions enables copper–aluminium bonding at significantly lower deformation degrees and improved properties compared to mechanical brushing. Laser ablation further increases interface contact area and induces favourable residual stress states and microstructural compatibility ...
Khemais Barienti, Finn‐Lennard Janthur, Selina Raumel, Sascha Jan Zimmermann, Sarah Seffer, René Gustus, Sebastian Herbst, Marc C. Wurz, Ludger Overmeyer, Wolfgang Maus‐Friedrichs, Hans Jürgen Maier, Florian Nürnberger   +11 more
wiley   +1 more source

The Analysis of the Cutting Forces and Surface Layer Stereometry in the Grinding Process of Abrasion-Resisting Materials [PDF]

, 2016
The article presents the investigation of the grinding process of flat samples made of materials that meet requirements of the lowest abrasibility, which belong to difficult to machine materials.
Grdulska, Anna, Rosik, Radosław, Wejman, Przemysław, Wójcik, Ryszard   +3 more
core  

Tribological Performance of 60NiTi Alloy Under Varying Contact Conditions and Elevated Temperatures in Linear Reciprocating Sliding

Advanced Engineering Materials, EarlyView.
This study investigates the tribological response of 60NiTi alloy under dry, water‐lubricated and high‐temperature conditions. The alloy exhibits decreasing wear volume and friction with increasing temperature due to the formation of protective oxide layers. The work clarifies dominant wear mechanisms and demonstrates the suitability of 60NiTi for high‐
Anthony Onyebuchi Okoani, Miguel Angel Selles, Maziar Ramezani   +2 more
wiley   +1 more source

Magnetic particle grinding and finishing test of mixed particle size abrasives

Jin'gangshi yu moliao moju gongcheng
ObjectivesMagnetic particle grinding finishing technology as an advanced processing technology can achieve high precision surface treatment. In order to simplify the test device, reduce the test cost and improve the processing effect, the single particle
Bingyang LIU, Yunlong DING, Wenjie SHAO, Bing HAN, Yan CHEN   +4 more
doaj   +1 more source

Abrasive processing mechanization of parts from polymeric composite materials for paste operation

Advanced Engineering Research, 2018
Introduction. The development of the final abrasive processing of parts from polymeric composite materials with the use of the flexible grinding tool is considered.
N. V. Kozulko
doaj   +1 more source

Experimental Verification of the Mechanical Resistance of Forensic Marking by Means Synthetic DNA [PDF]

, 2017
This article deals with experimental verification of resistance of forensic identification marks (microdots in combination with artificial DNA) to property. It is considered mechanical abrasion from potential offender to remove or damage readability of
Hütter, Marek, Los, Ondřej, Ščurek, Radomír   +2 more
core   +1 more source

Reduction of Oxide Inclusions During the High‐Frequency Welding of Steel via a Nonthermal Ar/H2 Plasma Jet

Advanced Engineering Materials, EarlyView.
High‐frequency (HF) welding of steel is limited by oxide inclusions that degrade weld quality. This study demonstrates, for the first time, the integration of a nonthermal Ar/H2 dielectric barrier discharge (DBD) plasma jet into HF welding. Local plasma treatment provides effective shielding and in‐situ oxide reduction, resulting in markedly fewer and ...
Viktor Udachin, Lienhard Wegewitz, René Gustus, Henning Wiche, Wolfgang Maus‐Friedrichs   +4 more
wiley   +1 more source