Results 111 to 120 of about 1,941 (227)

Preliminary Studies into Cutting of a Novel Two Component 3D-Printed Stainless Steel-Polymer Composite Material by Abrasive Water Jet. [PDF]

Materials (Basel), 2023
Szatkiewicz T, Perec A, Radomska-Zalas A, Banaszek K, Balasz B.   +4 more
europepmc   +1 more source

Talc‐Tempered Pottery From Bala Hissar, Kabul: An Analytical Study

Archaeometry, EarlyView.
ABSTRACT Potsherds of cooking ware excavated at Bala Hissar archaeological site in Kabul were studied using X‐ray fluorescence (XRF), scanning electron microscope‐energy dispersive X‐ray spectrometry (SEM‐EDS), Raman spectroscopy, X‐ray powder diffraction (XRPD), thermogravimetric analysis (TGA) and optical microscopy.
Parviz Holakooei, Babak Rafiei‐Alavi, Hafizullah Hazim, Hasti Pezeshkanjalili, Lara Maritan   +4 more
wiley   +1 more source

An Exploration of the Influence of Abrasive Water Jet Pressure on the Friction Signal Characteristics of Fixed Abrasive Lapping Quartz Glass Based on HHT. [PDF]

Micromachines (Basel), 2023
Zheng Y, Zhang Z, Wang Z, Pang M, Ma L, Su J.   +5 more
europepmc   +1 more source

Submerged geomorphic record of Quaternary palaeoshorelines: terraces and clinothems along a shelf‐edge in the Žirje Archipelago, Adriatic Sea

Boreas, EarlyView.
Numerous studies have shown that during the Quaternary there were substantial fluctuations in sea level in response to glacial–interglacial climate variability, reaching lowstand positions up to 134 m below the present sea level (b.s.l.). These fluctuations have had a strong influence on the morphology of shallow shelf seas, which preserve evidence of ...
Ozren Hasan, Dea Brunović, Natalia Smrkulj, Maria Geraga, Dimitris Christodoulou, Nikolina Ilijanić, George Papatheodorou, Slobodan Miko   +7 more
wiley   +1 more source

Impact of Preparation of Titanium Alloys on Their Abrasive Water Jet Machining. [PDF]

Materials (Basel), 2021
Štefek A, Tyč M.
europepmc   +1 more source

Experimental study on cutting depth of hard alloy by abrasive water jet

Jin'gangshi yu moliao moju gongcheng, 2016
By cutting experiments of hard alloy using high pressure abrasive water-jet,the influences of jet pressure,cutting speed,abrasive flow rate and target distance on the cutting depth are analyzed using single factor method.Based on the single factor tests ...
SONG Jinlai, GUAN Yancong, ZHAO Hongwei, SUN Yanbin   +3 more
doaj  

Implantoplasty Positively Influences Biofilm Removal During Toothbrush: An In Vitro Study

International Journal of Dental Hygiene, EarlyView.
ABSTRACT Purpose To analyse the effect of implantoplasty on the efficacy of brushing dental implants. Methods Acrylic hemi‐arches were made to simulate a horizontal bone loss condition in an implant in position 46, exposing 3 mm of its cervical intra‐osseous portion. Implantoplasty was performed on the implant surfaces of the test group, and no surface
Robson Iralla Rezende, Cleverson O. Silva   +1 more
wiley   +1 more source

Theoretical Modeling Method for Material Removal Characteristics of Abrasive Water Jet Polishing under Rotating Oblique Incidence. [PDF]

Micromachines (Basel), 2022
Zhang Z, Song C, Shi F, Tie G, Zhang W, Wang B, Tian Y, Hou Z.   +7 more
europepmc   +1 more source

The Effect of Mechanical Instrumentation on Dental Hard Tissue In Vitro: A Systematic Review

International Journal of Dental Hygiene, EarlyView.
ABSTRACT Objective The aim of this review was to analyse the effects of hand instruments, ultrasonic scalers and air polishing devices on dental hard tissues, focusing on material loss and surface roughness. Methods Electronic databases MEDLINE, EMBASE, and the Cochrane Library were screened for relevant studies.
Katerina Mezquita Prieto Dvorska, Chun Ching Liu, Patrick Schmidlin   +2 more
wiley   +1 more source

Process Parameter Modeling and Optimization of Abrasive Water Jet Dressing Fixed-Abrasive Pad Based on Box-Behnken Design. [PDF]

Materials (Basel), 2022
Wang Z, Wang S, Ding Y, Yang Y, Ma L, Pang M, Han J, Su J.   +7 more
europepmc   +1 more source