Advanced Science, EarlyView.By adjusting Ga's doping in Cu–Sn alloy, an ultra‐high elongation of 100.8% is achieved in first time. Ga forms a stable solid solution structure and a stronger electron exchange with Cu. This enhances strength‐ductility synergistically by tuning SFE to balance twinning and slip.
Dazhuo Song +15 more
wiley +1 more source
Slicing of silicon into sheet material: Silicon sheet growth development for the large area silicon sheet task of the Low Cost Silicon Solar Array project [PDF]
, 1978 The limits of blade tolerance were defined. The standard blades are T-2 thickness tolerance. Good results were obtained by using a slurry fluid consisting of mineral oil and a lubricity additive.
Fleming, J. R.
core +2 more sources
Advanced Science, EarlyView.High electrical performance alone does not guarantee efficient bioelectronic signal transduction. Despite excellent mixed ionic‐electronic conduction, recordings from cardiomyocytes reveal that p(g2T‐TT)‐based OECTs predominantly transduce field potential FP‐like signals due to weak cell‐polymer coupling.
Giulia Zoe Zemignani +10 more
wiley +1 more source
Combining the Pitcher and Lotus Plant: Supericephobic and Superhydrophobic Silicone Films
Advanced Science, EarlyView.Based on bench‐top nanomolding of polydimethylsiloxane (PDMS) with optimized silicone oil content, we developed hierarchically structured silicone films by essentially combining the properties of the lotus and pitcher plant; particularly we are able to achieve water contact angle as high as 171° and ice adhesion strength as low as 11.5 kPa (i.e ...
Cliff L. W. Ng +4 more
wiley +1 more source
Environmental Impact of Silicic Magmatism in Large Igneous Province Events
Geophysical Monograph Series, Page 133-151., 2021 Exploring the links between Large Igneous Provinces and dramatic environmental impact
An emerging consensus suggests that Large Igneous Provinces (LIPs) and Silicic LIPs (SLIPs) are a significant driver of dramatic global environmental and biological changes, including mass extinctions.
Scott E. Bryan
wiley +1 more source
, 1982 An acoustic oral hygiene unit is described that uses acoustic energy to oscillate mild abrasive particles in a water suspension which is then directed in a low pressure stream onto the teeth.
Heyman, J. S.
core +1 more source
Influence of machining parameters on part geometrical error in abrasive waterjet offset-mode turning [PDF]
, 2014 Geometrical error in abrasive waterjet turned parts is an important challenge toward the commercialization of abrasive waterjet turning process. A systematic study has not been done yet to investigate the effects of process parameters on geometrical ...
Annoni, M. +3 more
core +1 more source
Designing Scalable Mechano‐Virucidal Nanostructured Acrylic Surfaces for Enhanced Viral Inactivation
Advanced Science, EarlyView.Can a surface be designed to physically break viruses? This study explores how nanoscale geometry—specifically the spacing of tiny pillars—can determine whether viruses remain intact or rupture. Using flexible acrylic and a scalable fabrication process, the authors develop nanopillared, transparent surfaces that show strong antiviral activity without ...
Samson W. L. Mah +14 more
wiley +1 more source
CFD simulation and experiments of abrasive water jet polishing for micropores
Jin'gangshi yu moliao moju gongchengObjectives: Femtosecond laser technology has become the primary method for micropore processing due to its high precision and low energy consumption. However, during the process, it is easy to cause microcracks and burrs in the micropores.
Zihan CUI +5 more
doaj +1 more source
BioResources, 2014 The impact of varying pressure, feed rate, and abrasive mass flow rate on the efficiency of an abrasive water jet cutting process was studied in this work. Recombinant bamboo samples with thicknesses of 5, 10, and 15 mm were cut by the abrasive water jet.
Rongrong Li +4 more
doaj +1 more source