Results 161 to 170 of about 13,731 (260)

Improving energy absorption capability of the hexagonal honeycomb and re-entrant structures using a combined hierarchical design. [PDF]

Sci Rep
Ashrafian MM, Hasanzadeh R.
europepmc   +1 more source

Experimental Characterization of Mycelium‐Based Composites Under Multiple Loading Conditions

Advanced Engineering Materials, EarlyView.
This study examines the mechanical response of mycelium‐based composites under compression, shear, and tension using mechanical testing and imaging methods. The comparison between unpressed and hot‐pressed specimens shows that hot pressing is associated with higher compression and shear stiffnesses.
Shaghayegh Elahi, Kimiya Tajik, Harvey Shaw, Matti Isakov, Sami Pajunen, Lauri Rautkari   +5 more
wiley   +1 more source

Broadband low-frequency sound absorption and high insulation in a clay-cement composite with hydrogel-foaming engineered gradient porosity. [PDF]

Sci Rep
Hou Z, Zhou Z, Chen X, Zhang K, Li H, Zheng Y, Wang L.   +6 more
europepmc   +1 more source

Compatibility of Methacrylate Based Resins Controls Interfacial Failure and Toughness in 3D‐Printed Multimaterial Composites

Advanced Engineering Materials, EarlyView.
This work shows that the mechanical performance of multimaterial digital light processing (DLP) printed thermoset composites is governed by resin compatibility and interfacial design rather than spatial patterning alone. Brittle and ductile resin combinations produced premature interfacial failure, while graded interfaces and mechanically compatible ...
Ahmed M. H. Ibrahim, Li Meng, Ahmad R. Najafi, Nicolas J. Alvarez   +3 more
wiley   +1 more source

An Ultra-Thin and Wideband Low-Frequency Absorber Based on Periodic Resistance Film. [PDF]

Materials (Basel)
Bao T, Liu P, Zhang T, Wang H, Zhang Y.
europepmc   +1 more source

Comparison of Triply Periodic Minimal Surface Energy Absorbers Under Uniaxial Compressive Loading

Advanced Engineering Materials, EarlyView.
This study investigates LCD 3D printed Triply Periodic Minimal Surface (TPMS) structures as mechanical energy absorbers. By comparing various base designs and layered combinations under uniaxial compression, it identifies that a Diamond‐Gyroid sandwich structure offers superior performance.
Sergej Grednev, Noah‐Lean Roschlaub, Anne Jung   +2 more
wiley   +1 more source

Energy Absorption of Curvilinear Hybrid Auxetic Honeycombs. [PDF]

Materials (Basel)
Li S, Qiu N, Liu W, Yang J, Gao Q.
europepmc   +1 more source

Influence of Si Content and Milling Duration on the Microstructure and Mechanical–Tribological Properties of AlCoCrFeNiSi High‐Entropy Alloys

Advanced Engineering Materials, EarlyView.
Si‐doped AlCoCrFeNi high‐entropy alloys are synthesized by mechanical alloying to reveal the effect of Si content and milling time on phase evolution, microstructural refinement, and tribological behavior. A transition from FCC to BCC structure, significant grain refinement, and enhanced hardness and wear resistance are achieved, with the 4 at% Si ...
Mustafa Okumuş, Mehmet Emin Demir, Sercan Özpınar   +2 more
wiley   +1 more source

Thermal-fluid-structure coupling simulation of filling process of storage tanks with ultra-low temperature and high-flow-rate. [PDF]

Sci Rep
Zhang Z, Chen T, Chen J.
europepmc   +1 more source

Microstructure, Thermal Transport, and Dry‐Sliding Tribology of Powder‐Metallurgy Al7075 Composites Reinforced With Sol–Gel‐Derived ZnO–rGO Hybrid Nanoparticles

Advanced Engineering Materials, EarlyView.
Sol–gel‐derived ZnO–rGO hybrid nanoparticles enable Al7075 powder‐metallurgy composites to achieve concurrent gains in hardness and thermal conductivity while markedly lowering friction and wear. The hybrid architecture couples ZnO‐based load support with rGO‐assisted lamellar sliding and heat spreading, revealing a promising route toward lightweight ...
Bunyamin Aksakal, Cevher Kursat Macit, Merve Ayık, Hakan Tutumlu   +3 more
wiley   +1 more source