Results 81 to 90 of about 9,074 (311)

Health Care Use Among Patients Presenting to Emergency Department for Gout Flares in Ontario, Canada: A Population‐Based Health Systems Analysis

Arthritis Care &Research, EarlyView.
Objective We characterized emergency department (ED) gout visits and identified patient characteristics and health services patterns contributing to ED presentations. Methods We conducted a population‐based study of ED gout visits in Ontario, Canada, between 2014 and 2023.
Timothy S. H. Kwok, Samantha Morais, William K. Silverstein, Clare L. Atzema, Gregory Choy, Priyanka Chandratre, Ping Li, Jessica Widdifield   +7 more
wiley   +1 more source

An analytical formula for back EMF waveform of a counter‐rotating dual‐rotor non‐slotted axial flux permanent magnet synchronous machine

IET Generation, Transmission & Distribution
Fractional slot concentrated winding (FSCW) permanent magnet (PM) machines are gaining more attention for low‐speed applications because of their great advantages.
Reza Mirzahosseini, Elham Rahimi Namaghi
doaj   +1 more source

Electrochemical Evaluation of Compressed Selective Laser Melted AlSi7Mg and AlSi10Mg Alloys in Chloride Environment

Advanced Engineering Materials, EarlyView.
The corrosion performance of AlSi7Mg and AlSi10Mg alloys produced through selective laser melting (SLM) was examined under compressive stress in a chloride environment. Electrochemical analyses, including open‐circuit potential (OCP), potentiodynamic polarization (CPP), and electrochemical impedance spectroscopy (EIS), were complemented by scanning ...
Femi John Akinfolarin, Samson Dare Oguntuyi, Peter Apata Olubambi   +2 more
wiley   +1 more source

Innovative Processing of Compacted Waste Aluminum Alloy Powders via Controlled Remelting and Solidification

Advanced Engineering Materials, EarlyView.
This study demonstrates an efficient recycling route for out‐of‐spec AlSi10Mg atomized powders through compaction and arc remelting followed by suction casting. By correlating compaction load, cooling rate, and resulting microstructure, we show that intermediate pressures (50–80 kN) and rapid cooling refine dendrites, reduce porosity, and enhance ...
Mila Christy de Oliveira, Marcella Gaute Cavalcante Xavier, Abdoul‐Aziz Bogno, Piter Gargarella, José Eduardo Spinelli   +4 more
wiley   +1 more source

Application of Power Droop Control in Multi-motor AC Drive System

Kongzhi Yu Xinxi Jishu, 2020
Aiming at the problem of uneven distribution of output torque in multi-motor AC drive system with hard fixed joint, this paper proposed a power droop based torque balance control strategy, which enables the converter to balance the torque of two AC ...
HU Xian, WEN Yuliang, HU Liang
doaj  

Analysis of Effects of Magnetic Slot Wedges on Characteristics of Large Induction Motors

, 2011
Magnetic slot wedges are often used to improve starting performance of large induction motors. In this paper we have investigated – through simulation – the effects of the wedges on the performance characteristics of the motor and core losses under no ...
Dems, M., Komeza, K., Sykulski, J.K.
core  

Creep‐Induced Microstructural Evolution in an A2‐B2 Superalloy

Advanced Engineering Materials, EarlyView.
A 27.3Ta‐27.3Mo‐27.3Ti‐8Cr‐10Al (at.%) refractory high‐entropy alloy with precipitation‐strengthened A2‐B2 microstructure was studied by creep tests at 1030°C, which demonstrate a transition in deformation mechanisms in the range of 100–150 MPa applied stress. This is associated with changes in dislocation–precipitate interactions. Relevant deformation
Liu Yang, Aparajita Pramanik, Sandipan Sen, Shubhashis Dixit, Marcel Muench, R. J. Vikram, Daniel Schliephake, Yolita M. Eggeler, Ankur Chauhan, Martin Heilmaier, Alexander Kauffmann   +10 more
wiley   +1 more source

AC losses calculation of parallel multi‐strand flat wire windings for automotive drive motor

IET Electric Power Applications
Automobile drive motor with flat wire winding has improved the slot fill factor and efficiency. However, under the current environment of drive motors development to high frequency and voltage, the increase in winding AC loss has weakened those ...
Peipei Yang, Yanping Liang, Jia Liu, Ke Zhang   +3 more
doaj   +1 more source

AC Loss Suppression of High-Speed Permanent Magnet Synchronous Motor for Vehicles Based on End Transposed Winding Method

IEEE Access
Flat wire winding has some advantages, such as a high slot fill factor and low vibration noise, which is a mainstream technology solution for vehicle drive motors. However, when the motors operate at high-speeds, high-frequency AC losses of the flat wire
Haigui Gong, William Cai, Mingchong Sun, Ying Xie, Yue Tang, Shoulun Guo, Yongxi Yang, Zhanxi Lin, Zhiran Su, Xuesheng Jiang   +9 more
doaj   +1 more source

High‐Temperature Nanoindentation of Metals: Assessing Thermal Drift, Frame Compliance, and Chemical Composition Effects on the Reported Mechanical Properties

Advanced Engineering Materials, EarlyView.
Do not let thermal drift and instrument artifacts deceive high‐temperature nanoindentation results. We compare classical Oliver–Pharr and automatic image recognition analyses across steels and a Ni alloy to quantify these effects. Accounting for artifacts reveals systematic softening with temperature, while Cr and Ni additions boost resistance ...
Velislava Yonkova, Steffen Brinckmann, Ruth Schwaiger   +2 more
wiley   +1 more source