Results 271 to 280 of about 1,486,900 (338)

Assessing the Microstructure of SnBiZn Alloys during Semisolid Treatment

Advanced Engineering Materials, EarlyView.
The development of Sn‐based alloys for semisolid processing is crucial for Industry 4.0. This study investigates Sn40Bi and Sn40Bi2Zn alloys, revealing that Zn refines Sn‐rich globules by pinning dendrite boundaries. Bi saturation occurs at 60 min, while Zn enhances globule microhardness at 90 min through solid solution strengthening.
Carolina de Siqueira Simioli, Guilherme Lisboa de Gouveia, José Eduardo Spinelli   +2 more
wiley   +1 more source

Seismic performance analysis of braced steel structures based on vibration experiments and finite element simulation. [PDF]

PLoS One
Cui N, Liu S.
europepmc   +1 more source

A Simulative Approach for the Prediction of Mesoscale Residual Stress Fields in Solution‐Strengthened Ferritic Ductile Iron

Advanced Engineering Materials, EarlyView.
This study presents a 3D representative volume element‐based simulation approach to predict mesoscopic residual stress and strain fields in silicon solid solution‐strengthened ductile cast iron. By modeling phase transformation kinetics with an enhanced Johnson–Mehl–Avrami–Kolmogorov model, the effects of varying cooling rates on residual stresses are ...
Lutz Horbach, Oliver Schenk, Valérian Iss, Ali Rajaei, Jiali Zhang, Felix Weber, Christoph Broeckmann   +6 more
wiley   +1 more source

Correction for Izdebski et al., Unbalanced social-ecological acceleration led to state formation failure in early medieval Poland. [PDF]

Proc Natl Acad Sci U S A
europepmc   +1 more source

Flight route EDR estimation using MHE to fuse three-dimensional wind information in the QAR data analysis. [PDF]

PLoS One
Wei H, Li H, Liu W, Zhuang Z, Chen J.
europepmc   +1 more source

Process Parameter and Dimension‐Dependent Mn Vaporization During Laser Powder Bed Fusion of an Fe–Mi–Si–Cr‐Based Shape Memory Alloy

Advanced Engineering Materials, EarlyView.
The functional properties of Fe–Mn–Si–Cr‐based shape memory alloys are influenced, among other things, by their chemical composition. Here, the vaporization of Mn, the most volatile element of the alloy, is investigated. It is shown that the process parameters make noninterchangeable contributions to the vaporization and that vaporization differences ...
Maylin Homfeldt, Anastasiya Toenjes
wiley   +1 more source

Mechanical Behavior and Microstructural Changes Associated with Tensile Deformation above the Martensite Start Temperature during Quenching and Subsequent Partitioning of a Low‐Alloy 37SiB6 Steel

Advanced Engineering Materials, EarlyView.
A new experimental setup, incorporating digital image correlation and infrared thermography in combination with inductive‐conductive heating for precise temperature control, is used to analyze the mechanical behavior and microstructural changes of sheet metal under complex thermomechanical test conditions that represent quench and partitioning ...
Christian Illgen, Benjamin Bohne, Sven Winter, Marcus Böhme, Martin F.-X. Wagner   +4 more
wiley   +1 more source

Multimaterial Approach to Improve the Mechanical Properties of a Novel Modified Auxetic Reentrant Honeycomb Structure

Advanced Engineering Materials, EarlyView.
A multimaterial approach is introduced to improve upon auxetic structures by combining two different polymers into the same reentrant honeycomb structure via additive manufacturing. The deformation behavior as well as the resulting Poisson's ratio are thereby improved significantly.
Alexander Engel, Oraib Al‐Ketan, Anne Jung   +2 more
wiley   +1 more source

Vibration Analysis and Vehicle Detection by MEMS Acceleration Sensors Embedded in PCC Pavement. [PDF]

Sensors (Basel)
Chang C, Kong L, Han L, Li J, Pan S, Wei Y.   +5 more
europepmc   +1 more source

Residual Stress States in Microstructurally Graded PBF–LB/M Austenitic Steel Components

Advanced Engineering Materials, EarlyView.
This study examines microstructurally graded 316L rectangular tube profiles fabricated via PBF–LB/M using a dual‐laser system. A 1 kW top‐hat and a 400 W Gaussian laser create distinct grain sizes and crystallographic texture. Mechanical properties are linked to microstructural evolution driven by processing conditions.
Nico Möller, Florian Loebich, Thomas Wegener, Julia Richter, Jens Gibmeier, Thomas Niendorf   +5 more
wiley   +1 more source