Results 61 to 70 of about 27,270 (239)
KARAKTERISASI PELIKEL YANG TERADSORPSI PADA PERMUKAAN RESIN AKRILIK
Journal of Dentistry Indonesia, 2015 This research was aimed to determine the composiiton of adsorbed pellicle on acrylic resin surface. Fifteen plates of 10x10x2 mm were made from chemical, heat, and microwave activated acrylic resin.
Siti Sunarintyas, Dyah Irnawati
doaj +1 more source
High thermal conductivity of bulk epoxy resin by bottom-up parallel-linking and strain: a molecular dynamics study [PDF]
arXiv, 2018 The ultra-low thermal conductivity (~0.3 Wm-1K-1) of amorphous epoxy resins significantly limits their applications in electronics. Conventional top-down methods e.g. electrospinning usually result in aligned structure for linear polymers thus satisfactory enhancement on thermal conductivity, but they are deficient for epoxy resin polymerized by ...
arxiv
Accuracy of repaired maxillary dentures from two different repairing techniques: In vitro study
HeliyonBackground: Denture fracture is a common problem with acrylic dentures. The fractured denture can be repaired using various techniques such as self-cure acrylic resin acrylic resin and fiber-reinforced acrylic resin.
Sara Zaky Mohamed +5 more
doaj
Saudi Dental Journal, 2014 Objective: The purpose of this study was to compare the effects of mechanical polishing (MP) and chemical polishing (CP) on the average surface roughness (Ra) of heat-cured (HC) and light-cured (LC) denture base acrylic resins.
Abdul Aziz Abdullah Al-Kheraif
doaj
International Journal of DentistryConclusions: For improving the adhesion of AMH to acrylic resin of overdentures, the application of G-Premio BOND with or without ALLOY PRIMER in Ti substrate and Quick Up and autopolymerizing acrylic resin to the acrylic resin of denture base produced ...
Mohammadreza Nakhaei +3 more
doaj +1 more source
Turkish Journal of Orthodontics, 1997 In dental practice, acrylic resin base appliances should be kept in varions chemical disinfecting solutions, before and after laboratory stage and also after application to the patient, against cross-contamination.
A. İhya Karaman +2 more
doaj +1 more source
Effect of silica layer on bonding strength of thermoplastic nylon to cold cure acrylic resin
Journal of Baghdad College of Dentistry, 2014 Background: The combination of thermoplastic nylon resin materials and auto polymerizing resin is necessary in some situation for repair and adjustment.
Israa M Hummoudi
doaj
Flexural Strength of Cold and Heat Cure Acrylic Resins Reinforced with Different Materials
Frontiers in Dentistry, 2016 Objectives: Heat-polymerized acrylic resin has been the most commonly used denture base material for over 60 years. However, the mechanical strength of acrylic resin is not adequate for long-term clinical performance of dentures.
Bijan Heidari +4 more
doaj
Novel Bismaleimide Resin/Silsesquioxane and Titania Nanocomposites by the Sol-Gel Process: the Preparation, Morphology, Thermal and Thermo-mechanical Properties [PDF]
arXiv, 2013 Bismaleimide(BMI) resin/silsesquioxane or titania nanocomposites were synthesized from bismaleimide resin and SiO3/2 or TiO2 via the sol-gel process of N-{\gamma}-triethoxylsilylpropyl-maleamic acid (TESPMA) or tetrabutyltitanate (Ti(OnBu)4, TBT), respectively, in the presence of the AP-BMI prepolymers.
arxiv
Turkish Journal of Orthodontics, 2013 Objective:To evaluate the effects of one denture cleanser on the surface roughness of heat-cured and cold-cured acrylic resin materials.Materials and Methods:Two acrylic resin materials (one heat cured and one cold cured) were used in this study.
Nursel Arici, Cagri Ural
doaj +1 more source