Results 121 to 130 of about 3,561,042 (355)
Fracture strength and adhesive strength of hydroxyapatite-filled polycaprolactone
Journal of Materials Science: Materials in Medicine, 2007 Fracture toughness and tear strength of hydroxyapatite (HAP)-filled poly(epsilon-caprolactone) (PCL) with increasing HAP concentration were studied. The toughness was assessed in terms of essential work of fracture (EWF). Adhesive strength between HAP and PCL interfaces was evaluated using T-peel testing.
Shing-Chung, Wong, Avinash, Baji
openaire +2 more sources
Dynamic Precipitation during High‐Pressure Torsion of a Magnesium–Manganese Alloy
Advanced Engineering Materials, EarlyView.An ultrafine‐grained alloy is produced by high‐pressure torsion of solutionized Mg–1.35 wt% Mn. Precipitation of nanometer‐scale Mn particles during deformation provides pinning sites. This prevents the formation of a bimodal grain structure and results in a finer grain size than for pure Mg.
Julian M. Rosalie, Anton Hohenwarter
wiley +1 more source
Advanced Engineering Materials, EarlyView.The effect of temperature controllers that are commonly used in freeze‐casting is investigated in this work. Temperature controllers are observed to generate a voltage in the slurry. Microstructural alignment and ultimate compressive strength data show this voltage to interfere with the ability to align the microstructure using magnetic fields ...
Maddie A. Schmitz, Steven E. Naleway
wiley +1 more source
Advanced Engineering Materials, EarlyView.This article describes the preparation and characterization of poly(ε‐caprolactone) electrospun composite fibers incorporating sol‐gel‐derived bioactive glass particles doped with B and Cu. Scanning electron microscopy, energy‐dispersive X‐ray spectroscopy, Fourier‐transform infrared spectroscopy, contact angle, acellular bioactivity, mechanical and ...
Elisa Piatti +5 more
wiley +1 more source
Evaluation of wood surface coating performance using water based, solvent based and powder coating
Maderas: Ciencia y Tecnología, 2019 The objective of this study was to evaluate the surface coating performance using water base, solvent base and powder coating on medium density fiberboard. Samples were coated using water-base, solvent-base and powder coating.
Ender Hazir, Kücük Huseyin Koc
doaj
Adhesion strength of the cathode in lithium-ion batteries under combined tension/shear loadings
, 2018 To understand the failure mechanism and establish reliable deformation tolerances for lithium-ion batteries under mechanical loading, accurate testing and modeling of individual components are indispensable.
Hailing Luo +3 more
semanticscholar +1 more source
Advanced Engineering Materials, EarlyView.The release of foulers from protective marine coatings is determined by several interrelated material properties, including the strength of Young's modulus, the flexibility of chain segments, the surface free energy, and the magnitude of hydrodynamic stress.
Johann C. Schaal +2 more
wiley +1 more source
Effects of Carbon Nanoparticles on Triboelectro‐Induced Surface Defects
Advanced Engineering Materials, EarlyView.Carbon nanoparticles added to grease modify the electrocontact behavior. The synergy of particle concentration and electric current dominates the surface damage of metals in contact. Electrical surface damage caused by current leakage is a critical challenge in high‐performance applications such as electric vehicle (EV) drivetrains and wind turbine ...
Mohsen Tajedini +6 more
wiley +1 more source
The surface properties of carbon fibers and their adhesion to organic polymers [PDF]
The state of knowledge of the surface properties of carbon fibers is reviewed, with emphasis on fiber/matrix adhesion in carbon fiber reinforced plastics.
Bascom, W. D., Drzal, L. T.
core +1 more source
The influence of cobalt on the microstructure and adherence characteristics of enamel on steel sheet [PDF]
, 2011 In this study, the influence of cobalt (Co) on the microstructure and adhesion between enamel and steel substrate has been investigated. The result of press test indicated that the adhesion strength was greatly improved by Co inclusion.
Amin Davarpanah, Masoud Bodaghi
core