Improving the adhesion strength of polymers: effect of surface treatments
Journal of Adhesion Science and Technology, 2020 To improve their adhesion strength, polymeric surfaces are usually modified through different treatments. This study investigates the effect of mechanical, chemical, and energetic treatments on the bonding strength of ethylene propylene diene methylene ...
Marouen Hamdi, M. N. Saleh, J. Poulis
semanticscholar +1 more source
Evaluate the effect of oil-heat treatment of Fir species on contact angle and adhesion strength of water based clear and acid catalyzed transparent coat [PDF]
تحقیقات علوم چوب و کاغذ ایران, 2015 In this research the effect of oil-heat treatment of Fir species (Abies spp) on contact angle and adhesion strength of organic solvent based and water based coating (acid catalyzed and acrylic water based coating) were investigated.
Mohammad Saleh Hosseini Fard +2 more
doaj +1 more source
3Y-TZP electrostatic painting to increase bond strength to dentin and dental prostheses
Journal of Materials Research and Technology, 2023 Although the clinical method used to improve the adhesion of zirconia prostheses to other materials is sandblasting or acid etching surface, the failure rate of the bond is high.
Alessandro Brito Thomaz +4 more
doaj +1 more source
Intermediate filament–membrane attachments function synergistically with actin-dependent contacts to regulate intercellular adhesive strength [PDF]
, 2002 By tethering intermediate filaments (IFs) to sites of intercellular adhesion, desmosomes facilitate formation of a supercellular scaffold that imparts mechanical strength to a tissue.
Amargo, Evangeline V. +11 more
core +5 more sources
Bond Strength and Adhesion Mechanisms of Novel Bone Adhesives
Bioengineering, 2023 Bone adhesives offer distinct advantages over the use of screws to attached internal fixation plates (IFPs). As the chemical composition of bone is similar to dentine, it is possible that the types of monomers used to make dentine adhesives could be utilised to affix IFPs to bone.
Sarah J. Upson +5 more
openaire +4 more sources
Investigation on the effect of different methods of applying transparent coatings on adhesion strength of coating in wooden surfaces [PDF]
تحقیقات علوم چوب و کاغذ ایران, 2016 In present study the effect of different methods of applying transparent coatings on adhesion strength of coating in Walnut (Juglans regia), Maple (Acer velutinum) and Pine (Pinus eldarica) species was investigated.
Mohammad Ghofrani +2 more
doaj +1 more source
High Fidelity Tape Transfer Printing Based On Chemically Induced Adhesive Strength Modulation [PDF]
, 2015 Transfer printing, a two-step process (i.e. picking up and printing) for heterogeneous integration, has been widely exploited for the fabrication of functional electronics system.
A Carlson +33 more
core +2 more sources
Tensile bond strength of maxillofacial adhesives
The Journal of Prosthetic Dentistry, 1993 A common technique for fixation of facial prostheses is the use of skin adhesives. The present study compared the tensile bond strength of five RTV-silicone elastomers used with four different skin adhesives to human skin. The elastomers were: Silskin II, MDX4-4210, Cosmesil, Cosmesil HC2, and RS 330 T-RTV.
POLYZOIS, GL, OILO, G, DAHL, JE
openaire +3 more sources
Effect of Heartwood and Sapwood Ratio on Adhesion Strength of Finished Wood Species
Advances in Materials Science and Engineering, 2015 The objective of this study was to determine adhesion strength of samples from wood species coated with cellulose varnish as function of heartwood and sapwood ratio.
Turgay Ozdemir +2 more
doaj +1 more source
Wet granulation in laboratory scale high shear mixers: Effect of binder properties [PDF]
, 2011 The effect of binder properties on torque curves, granule growth kinetics, wet mass consistency and dry granule strength has been investigated in this study.
Chitu, Toma Mihai +2 more
core +3 more sources