Results 291 to 300 of about 997,096 (396)

Tribology of ZrC Coatings and Spherical Tips Acquired with Extraordinarily Stiff, Metal Atomic Force Microscopy Probes

Advanced Engineering Materials, EarlyView.
In this research, ZrC coatings are evaluated against various counterprobes at the microscale using novel super‐stiff atomic force microscopy cantilevers. The chemical composition of the coating is shown to be an important factor influencing coating hardness and Young's modulus, while surface roughness, counterprobe hardness, and surface energy are the ...
Piotr Jenczyk, Marcin Michałowski, Bogdan Warcholiński, Michał Milczarek, Adam Gilewicz   +4 more
wiley   +1 more source

Dynamic characteristics study of composite base plate: numerical simulation, processing technology research and modal analysis. [PDF]

Sci Rep
Wang F, Yang G, Li L, Chang X.
europepmc   +1 more source

From Nature to Engineering: Mortar Volume and Interfacial Mechanics in Bioinspired Ceramics

Advanced Engineering Materials, EarlyView.
Inspired by natural armors like nacre, this study explores how varying the volume fraction of the soft mortar layer impacts the interfacial strength and toughness of bioinspired ceramics. Experimental and computational analysis reveals that higher mortar volumes increase energy dissipation but reduce interfacial stiffness, offering insights for ...
Ehsan Azad, Hamidreza Yazdani Sarvestani, Behnam Ashrafi, Farjad Shadmehri, Mehdi Hojjati   +4 more
wiley   +1 more source

Anti-fatigue adhesive non-swelling hydrogel constructed by covalent topological structure and micro-nano gel for stretchable bioelectronics. [PDF]

Bioact Mater
Tian G, Zhu M, Chen J, Liang C, Zhao Q, Yang D, Liu Y, Tang S, Huang J, Liu Z, Lu W, Zhu M, Yan W, Qi D.   +13 more
europepmc   +1 more source

Quality Enhancement of Laser Powder‐Bed Fusion Parts by Acoustically Assisted Additive Manufacturing by Laser Powder‐Bed Fusion and its Application to Lattice Structures

Advanced Engineering Materials, EarlyView.
Additive manufacturing technologies like laser powder‐bed fusion offer great design freedom and individualization of products down to a batch size of one. However, parts fabricated with this technology suffer from poor quality. Acoustic assistance during the build process can minimize these drawbacks.
Oliver Maurer, Dirk Bähre
wiley   +1 more source

Packing and flow performance of binary adhesive mixtures for inhalation of different drug loads and their relationships to aerosolisation. [PDF]

Int J Pharm X
Simonsson A, Bramer T, Wimbush A, Alderborn G.   +3 more
europepmc   +1 more source

Mechanical Behavior and Microstructural Changes Associated with Tensile Deformation above the Martensite Start Temperature during Quenching and Subsequent Partitioning of a Low‐Alloy 37SiB6 Steel

Advanced Engineering Materials, EarlyView.
A new experimental setup, incorporating digital image correlation and infrared thermography in combination with inductive‐conductive heating for precise temperature control, is used to analyze the mechanical behavior and microstructural changes of sheet metal under complex thermomechanical test conditions that represent quench and partitioning ...
Christian Illgen, Benjamin Bohne, Sven Winter, Marcus Böhme, Martin F.-X. Wagner   +4 more
wiley   +1 more source

Antimicrobial Titanium–Copper Alloys: The Role of Microstructure in Arc‐Melted Compositions

Advanced Engineering Materials, EarlyView.
Copper‐containing titanium alloys show promise in combating orthopedic implant infections. This study explores the influence of heat treatment on Ti‐11.5Cu and Ti‐33Cu alloys, revealing that larger Ti2Cu precipitates (≈5 μm) enhance antimicrobial efficacy through increased surface contact. Results suggest contact sterilization is the primary mechanism,
Daisy Rabbitt, Paraic O’Kelly, Victor M. Villapún, Luke N. Carter, Alexander J. Knowles, Sophie C. Cox   +5 more
wiley   +1 more source

Study on the Performance of Composite-Modified Epoxy Resin Potting Adhesive for Repairing Oblique Cracks. [PDF]

Materials (Basel)
Chen Z, Li Z, Ran Z, Zhang Y, Lin F, Zhou Y.   +5 more
europepmc   +1 more source