Results 51 to 60 of about 19,253 (200)

Plastic Shrinkage Cracking in Concrete

open access: yesProceedings, 2019
Plastic shrinkage cracking in concrete is mainly a physical process, in which chemical reactions between cement and water do not play a decisive role. It is commonly believed that rapid and excessive moisture loss, due to evaporation is the primary cause
Faez Sayahi   +3 more
doaj   +1 more source

Electrochemical Behavior of Flame‐Sprayed Sc‐Doped AlCoCrFeMo High‐Entropy Alloy Coatings in 3.5% Sodium Chloride Solution

open access: yesAdvanced Engineering Materials, EarlyView.
Scandium (Sc)‐doped AlCoCrFeMo HEA coatings are fabricated via flame spraying with 0.1, 0.3, and 0.5 wt% Sc additions. Among these, the HEA‐Sc0.3 coating exhibits the highest corrosion resistance, indicated by a more positive corrosion potential and lower current density.
Pankaj Kumar   +7 more
wiley   +1 more source

Inverse Identification of Energy‐Dependent Laser Absorptivity in NiTi Laser Powder‐Bed Fusion via Calibrated Melt Pool Simulation

open access: yesAdvanced Engineering Materials, EarlyView.
A combined experimental–computational framework identifies energy‐dependent laser absorptivity for NiTi in laser powder‐bed fusion, applicable to conduction and transition modes. Single‐track experiments and thermofluid smoothed particle hydrodynamics simulations are coupled through inverse analysis of melt pool geometry.
Mohamadreza Afrasiabi   +3 more
wiley   +1 more source

Effect of AEA-SP Dosage Sequence on Air Entrainment in FA Concrete

open access: yesNordic Concrete Research, 2019
Laboratory measurements show that varying the dosage sequence of air-entraining agent and co-polymer in the mix (SP added before, after or together with AEA) greatly affects air entrainment in fresh and hardened fly ash concrete.
Shpak Andrei, Jacobsen Stefan
doaj   +1 more source

Comparison of Triply Periodic Minimal Surface Energy Absorbers Under Uniaxial Compressive Loading

open access: yesAdvanced Engineering Materials, EarlyView.
This study investigates LCD 3D printed Triply Periodic Minimal Surface (TPMS) structures as mechanical energy absorbers. By comparing various base designs and layered combinations under uniaxial compression, it identifies that a Diamond‐Gyroid sandwich structure offers superior performance.
Sergej Grednev   +2 more
wiley   +1 more source

Stability of Air Content in Fresh Concretes with PCE-Based Superplasticizers

open access: yesNordic Concrete Research, 2019
Air contents of concrete are necessary for concrete durability in freeze-thaw exposure. According to the Finnish concrete code, the target value for air content varies between 4% and 5.5% for XF - exposure classes. Lately in Finland, some cases showed an
Al-Neshawy Fahim   +2 more
doaj   +1 more source

Effects of chemical and mineral admixtures on the foam indexes of cement-based materials

open access: yesCase Studies in Construction Materials, 2019
Air in cement-based materials is one of the important parameters affecting its properties in fresh and hardened states. Various types of chemical and mineral admixtures have been combined and used in cement-based materials.
Hai Huang   +4 more
doaj   +1 more source

Effects of Mg-based admixtures on chloride diffusion in alkali-activated fly ash-slag mortars [PDF]

open access: yes
This study evaluated the effects of various Mg-based admixtures, including magnesium oxide (MgO), layered double hydroxides (LDH), and calcined layered double hydroxides (CLDH), on the chloride resistance of alkali-activated fly ash-slag (AAFS) mortars ...
Xiaocong Yang   +11 more
core   +1 more source

Influence of Scan Strategies in Electron Beam Powder Bed Fusion on Solidification, Microstructure, and High‐Temperature Compressive Properties of γ′‐Strengthened Inconel 738LC

open access: yesAdvanced Engineering Materials, EarlyView.
Experiments and thermophysical simulations were conducted to investigate the electron beam powder bed fusion electron beam (PBF‐EB/M) process for the γ′‐strengthened nickel‐based superalloy Inconel 738LC. The results demonstrate the impact of process‐induced microstructural variations on high‐temperature mechanical behavior, providing a basis for ...
Jan Niklas Petenati   +11 more
wiley   +1 more source

High‐Temperature Phase Transformation in a V‐9Si‐6.5B Alloy: The Kinetic and Crystallographic Pathway From V5SiB2 to V8SiB4

open access: yesAdvanced Engineering Materials, EarlyView.
In situ synchrotron high‐energy X‐ray diffraction reveals the real‐time high‐temperature phase evolution of a ternary V‐9Si‐6.5B alloy. The study uncovers a kinetically delayed V5SiB2 → V8SiB4 transformation governed by massive structural and chemical barriers.
Zahra Sabeti   +4 more
wiley   +1 more source

Home - About - Disclaimer - Privacy