Results 111 to 120 of about 1,139 (252)

Fabrication Routes for Ionic Conducting Fiber Strain Sensors

Advanced Engineering Materials, EarlyView.
Ionic conducting fiber strain sensors (ICFSs) offer compliant, textile‐integrable sensing. Thus far, the commercialization of ICFSs has been constrained by fiber fabrication routes. This review provides a fabrication‐centric analysis of ICFSs correlating processing strategies with material properties and scalability.
Leo John Kershaw, Zhanhong Yang, Anne Ladegaard Skov, Magdalena Skowyra   +3 more
wiley   +1 more source

Biomechanical and Aerodynamic Modulation for Sinonasal Homeostasis in Craniofacial Orthopedics: A Comprehensive Review of RAMPA Therapy. [PDF]

Biomimetics (Basel)
Mitani Y, Okai-Kojima Y, Moshfeghi M, Choi B, Hashimoto Y.   +4 more
europepmc   +1 more source

Rapidly Solidified High‐Strength Invar 36 Prepared by Planar‐Flow Melt Spinning

Advanced Engineering Materials, EarlyView.
The Invar 36 alloy was rapidly solidified using the planar‐flow melt‐spinning technique. Ribbon samples with thicknesses ranging from 20 to 160 mm were produced. As the grain size of the ribbon decreased to sub‐micron levels, the hardness increased by more than 2 times.
Bekir Akgül, Mehmet Kul
wiley   +1 more source

Dipteran flight diversity is shaped by aerodynamic constraints, scaling, and evolutionary trade-offs. [PDF]

PLoS Biol
Le Roy C, Bharathi I, Engels T, Muijres FT.   +3 more
europepmc   +1 more source

Gallium Microalloying in Bi–Sn Solders: Interfacial Phase Formation, Wettability, and Long‐Term Shear Reliability Under Isothermal Aging

Advanced Engineering Materials, EarlyView.
Gallium microalloying redirects interfacial reactions in low‐temperature Bi–Sn solders from Cu–Sn toward Cu–Ga intermetallic formation. The resulting Cu–Ga layer suppresses intermetallic growth during thermal aging, alters fracture pathways, and improves interfacial stability.
Iva Králová, Markéta Klimtová, Mohd Faizul Mohd Sabri, Yew Hoong Wong, Petr Veselý, Martin Plaček, Karel Dušek   +6 more
wiley   +1 more source

Morphology, Transport, and Dynamics of Protein Adsorption in Open‐Cell Metal Foam

Advanced Engineering Materials, EarlyView.
Stainless steel (SS) open‐cell foams are shown to adsorb more protein per unit area than previously reported 316L SS and chromium oxide surfaces under static and flow conditions. An integrated approach combining 3D pore imaging, flow simulation, and protein adsorption experiments characterizes the foam’s performance.
Chinmaya Prerana Inguva, Joseph Lavoie, Afsaneh Rabiei   +2 more
wiley   +1 more source

Nonlinear flexibility effects on flight dynamics of high-aspect-ratio wings. [PDF]

J Eng Appl Sci
Tantaroudas ND, Karachalios I.
europepmc   +1 more source

Feasibility and Limitations of the Advanced Replica Process for Bioactive Glasses

Advanced Engineering Materials, EarlyView.
Periodic 3D‐printed Kelvin‐cell templates enable a controlled advanced replica process for fabricating highly porous glass lattices. Across P45K9, 45S5, and 13–93, material‐dependent differences in coating, burnout, and shrinkage lead to distinct strut morphologies, while comparable final porosities of 83%–88% are retained.
Swantje Funk, Elisabeth Keck, Alberto López‐Grande, Delia S. Brauer, Tobias Fey   +4 more
wiley   +1 more source

Bridging Biology and Engineering: Unsteady Aerodynamics and Biomimetic Design of Micro Air Vehicles. [PDF]

Biomimetics (Basel)
Prisăcariu EG, Dumitrescu O.
europepmc   +1 more source

Mechanism of Aerodynamic Noise Generated from Front-Pillar and Door Mirror of Automobile(Fluids Engineering)

Transactions of the Japan Society of Mechanical Engineers Series B, 2009
Takahide NOUZAWA, Ye LI, Naohiko KASAKI, Takaki NAKAMURA   +3 more
openaire   +2 more sources