Results 91 to 100 of about 132,017 (306)

Comparison of Triply Periodic Minimal Surface Energy Absorbers Under Uniaxial Compressive Loading

Advanced Engineering Materials, EarlyView.
This study investigates LCD 3D printed Triply Periodic Minimal Surface (TPMS) structures as mechanical energy absorbers. By comparing various base designs and layered combinations under uniaxial compression, it identifies that a Diamond‐Gyroid sandwich structure offers superior performance.
Sergej Grednev, Noah‐Lean Roschlaub, Anne Jung   +2 more
wiley   +1 more source

Influence of Si Content and Milling Duration on the Microstructure and Mechanical–Tribological Properties of AlCoCrFeNiSi High‐Entropy Alloys

Advanced Engineering Materials, EarlyView.
Si‐doped AlCoCrFeNi high‐entropy alloys are synthesized by mechanical alloying to reveal the effect of Si content and milling time on phase evolution, microstructural refinement, and tribological behavior. A transition from FCC to BCC structure, significant grain refinement, and enhanced hardness and wear resistance are achieved, with the 4 at% Si ...
Mustafa Okumuş, Mehmet Emin Demir, Sercan Özpınar   +2 more
wiley   +1 more source

Design Model Data Exchange Between Concurrent Engineering Facilities by Means of Model Transformation [PDF]

, 2011
The German Aerospace Center (DLR) is developing the software Virtual Satellite for use in their Concurrent Engineering Facility. Throughout the design process of a spacecraft the software supports engineers to store and manage the data and results of ...
Schaus, Volker, Gerndt, Andreas, Fischer, Philipp M.   +2 more
core  

Microstructure, Thermal Transport, and Dry‐Sliding Tribology of Powder‐Metallurgy Al7075 Composites Reinforced With Sol–Gel‐Derived ZnO–rGO Hybrid Nanoparticles

Advanced Engineering Materials, EarlyView.
Sol–gel‐derived ZnO–rGO hybrid nanoparticles enable Al7075 powder‐metallurgy composites to achieve concurrent gains in hardness and thermal conductivity while markedly lowering friction and wear. The hybrid architecture couples ZnO‐based load support with rGO‐assisted lamellar sliding and heat spreading, revealing a promising route toward lightweight ...
Bunyamin Aksakal, Cevher Kursat Macit, Merve Ayık, Hakan Tutumlu   +3 more
wiley   +1 more source

Computational Fluid Dynamics Analysis in Biomimetics Applications: A Review from Aerospace Engineering Perspective. [PDF]

Biomimetics (Basel), 2023
Basri EI, Basri AA, Ahmad KA.
europepmc   +1 more source

Defect Evolution and Mechanical Performance of Fused Filament Fabrication‐Manufactured 17‐4PH Stainless Steel Revealed by X‐Ray Computed Tomography

Advanced Engineering Materials, EarlyView.
X‐ray computed tomography reveals how process‐induced defects evolve from green to sintered states in Fused Filament Fabrication (FFF)‐manufactured 17‐4PH stainless steel. Internal porosity, weakest cross‐sections, and fracture locations show strong correlation with tensile performance, demonstrating the potential of computed tomography (CT)‐based ...
György Ledniczky, Márk Sárközi, Ibolya Zsoldos, Zoltán Weltsch   +3 more
wiley   +1 more source

Silicified Wood‐Inspired, High‐Strength Fire‐Resistant Chitin‐Based Aerogels for Sustainable High‐Temperature Thermal Insulation

Advanced Functional Materials, EarlyView.
Inspired by natural silicified wood, a biomimetic mineralized chitin‐derived aerogel is constructed. It can withstand 81 000 times its own weight, and its backside temperature is 130.4°C after exposure to ∼1300°C butane flame for 600 s, exhibiting high‐strength, fire‐resistance, and super thermal‐insulation properties.
Kai Xu, Qihang Lv, Lubin Liu, Zhezhe Zhou, Chentao Yan, Ao Qin, Jianting Ma, Shuhui Liang, Yue Xu, Min Hong, Bin Li, Pingan Song   +11 more
wiley   +1 more source

Rapid near-optimal aerospace plane trajectory generation and guidance

, 1988
Issued as Progress reports [nos. 1-3], and Final report, Project no.
Calise, Anthony J.
core  

Value stream analysis of manufacturing engineering new product introduction processes [PDF]

, 2011
This paper describes the use of a methodology for value stream mapping and analysis of Manufacturing Engineering New Product Introduction processes. The applicability and usefulness of the technique to process improvement in this domain is explored in
Chris Beadle, Shehab, Essam, Essam Shehab, Malachy Maginness, Maginness, Malachy, Beadle, Chris   +5 more
core   +1 more source

3D Printing Innovations in Polymeric Porous and Patterned Architecture

Advanced Functional Materials, EarlyView.
Polymeric foams occupy a unique structural space between dense solids and open networks, where engineered void fraction governs mechanical compliance, thermal resistance, and mass transport. Additive manufacturing now enables precise spatial control over cellular architecture, unlocking designer foam structures across applications spanning crash ...
Dhanush Patil, Sri Vaishnavi Thummalapalli, Clarissa Westover, Arunachalam Ramanathan, M. Taylor Sobzcak, Roumika Patil, Qixuan Xiang, Tiantian Li, Sui Yang, Timothy E. Long, Hongyue Sun, Xianqiao Wang, Yang Liu, Kenan Song   +13 more
wiley   +1 more source