Results 81 to 90 of about 142,034 (268)
Advanced Engineering Materials, EarlyView.Sol–gel‐derived ZnO–rGO hybrid nanoparticles enable Al7075 powder‐metallurgy composites to achieve concurrent gains in hardness and thermal conductivity while markedly lowering friction and wear. The hybrid architecture couples ZnO‐based load support with rGO‐assisted lamellar sliding and heat spreading, revealing a promising route toward lightweight ...
Bunyamin Aksakal +3 more
wiley +1 more source
Numerical Study on Improving the Efficiency of the Earth Pipe Cooling System
E3S Web of Conferences, 2018 Earth pipe cooling (EPC) is one of the passive cooling systems which has proven to be a very energy efficient sustainable cooling technique for the sub-tropical areas. This cooling system uses the soil as a medium of heat transfer.
Saha Parnab +4 more
doaj +1 more source
Randomized cross-over study investigating the tolerability and side effects of an intra-oral air-cooling device compared to ice in healthy volunteers. [PDF]
Med Oncol, 2022 Blacker C +3 more
europepmc +1 more source
Active Corrosion Protection of Sintered AA7075 Aluminum Alloy via Mn Powder Addition
Advanced Engineering Materials, EarlyView.AA7075 containing Mn‐rich particles is fabricated via spark plasma sintering using AA7075 and Mn powders. Corrosion resistance is evaluated through dip‐and‐dry tests using 0.1 M NaCl (pH 6.0), and mass loss decreases with increasing Mn addition. Mn‐rich particles function as a source of Mn ions, and formation of Mn‐accumulation films on Cu‐containing ...
Ko Ebina, Masashi Nishimoto, Izumi Muto
wiley +1 more source
SIMULATION OF CONDENSATE PRODUCING PROCESSES DURING GAS TURBINE UNIT INTAKE AIR COOLING
Радіоелектронні і комп'ютерні системи, 2019 The processes of gas turbine unit intake air cooling with producing the condensate as a subproduct were simulated with using the computer programs of the firms-producers of the heat equipment for gas turbine unit intake air cooling waste heat recovery ...
Андрей Николаевич Радченко +3 more
doaj +1 more source
Advanced Engineering Materials, EarlyView.Experiments and thermophysical simulations were conducted to investigate the electron beam powder bed fusion electron beam (PBF‐EB/M) process for the γ′‐strengthened nickel‐based superalloy Inconel 738LC. The results demonstrate the impact of process‐induced microstructural variations on high‐temperature mechanical behavior, providing a basis for ...
Jan Niklas Petenati +11 more
wiley +1 more source
IEEE Access, 2018 Recently, the rapid growth in both data center power density and scale poses great challenges to the cooling system. On one hand, the data center operators try to over provision cooling resources for fear of server failures induced by accumulated heat ...
Jianxiong Wan +4 more
doaj +1 more source
Influence of pulse duration and water/air cooling ratio on the efficiency of Er:YAG 2940 nm laser in debonding of porcelain laminate veneers: An in vitro study. [PDF]
Clin Exp Dent Res, 2022 AlBalkhi M, Hamadah O.
europepmc +1 more source
Advanced Functional Materials, EarlyView.Shellac, a centuries‐old natural resin, is reimagined as a green material for flexible electronics. When combined with silver nanowires, shellac films deliver transparency, conductivity, and stability against humidity. These results position shellac as a sustainable alternative to synthetic polymers for transparent conductors in next‐generation ...
Rahaf Nafez Hussein +4 more
wiley +1 more source
Correction to: Primary evaluation of an air‑cooling device to reduce oral mucositis: a pilot study in healthy volunteers. [PDF]
Med Oncol, 2021 Blacker C +3 more
europepmc +1 more source