Results 41 to 50 of about 6,314 (249)

Influence of Test Temperature and Test Frequency on Fatigue Life of Aluminum Alloy EN AW‐2618A

Advanced Engineering Materials, EarlyView.
The influence of test temperature and test frequency on the fatigue life of EN AW‐2618A is investigated. High‐cycle fatigue tests are performed at different test temperatures and frequencies on the 1000 h/230°C overaged state. Both test parameters reduce fatigue life due to time‐dependent damage mechanisms.
Ying Han, Julian M. Rosalie, Jan Radners, Mauro Madia, Philipp von Hartrott, Birgit Skrotzki   +5 more
wiley   +1 more source

Investigation of the Fluid-Solid Thermal Coupling for Rolling Bearing under Oil-Air Lubrication

Advances in Mechanical Engineering, 2015
An excellent oil-air lubrication system helps to improve rolling bearing's working conditions and thus extend its service life span. Flowing and heat dissipating characteristics of oil-air media inside bearing chamber are very complicated due to the ...
Baohong Tong, Guangyu Wang, Xiaoqian Sun
doaj   +1 more source

Current Status and Challenges in Data Collection for Aerospace Coatings Deposited by Plasma Spraying

Advanced Engineering Materials, EarlyView.
An innovative approach has been integrated into the GRENAT project to optimize plasma spraying and coating performance. Raw materials are accelerated and melted in the plasma generated by torches, creating coatings. Monitoring sensors collect process data which are combined with ex situ characterization data.
Lila Randriamananjara, Vincent Rat, Quentin Dubreuil, Patrice Valorge, Simon Goutier, Alain Denoirjean, Olivier Messe, Céline Ruelle, Jean‐Philippe Poli   +8 more
wiley   +1 more source

Direct Metal Deposition of Graphene–Ti28Nb35.4Zr Matrix Composites With Enhanced Mechanical, Corrosion, and Biocompatibility Properties for Bone Implants

Advanced Engineering Materials, EarlyView.
Graphene nanoplatelet (0.1 wt.%) reinforcement significantly enhances the performance of β Ti‐28Nb‐35.4Zr alloy. Grain refinement, reduced water contact angle, and improved surface characteristics promote osteoblast adhesion and complete surface coverage after 7 days.
Khurram Munir, Jixing Lin, Yuncang Li, Li Zhu, Paul F. A. Wright, Cuie Wen   +5 more
wiley   +1 more source

Cathodic Cage Plasma Deposition of Nanostructured Cu–Fe–Se Coatings on Poly(methyl Methacrylate)

Advanced Engineering Materials, EarlyView.
Nanostructured Cu–Fe–Se coatings are deposited on PMMA by a modified cathodic cage plasma process, enabling low‐temperature deposition on polymer substrates. A transition from discontinuous to compact morphology is observed with temperature, with optimal properties at 200°C, where improved CuFeSe2‐type bonding, lowest sheet resistance, and favorable ...
V. S. S. Sobrinho, M. Naeem, T. H. C. Costa, M. S. Libório, J. C. A. Queiroz, C. B. B. Luna, R. R. M. Sousa, P. S. Vieira, E. M. Araújo   +8 more
wiley   +1 more source

Microstructure, Thermal Transport, and Dry‐Sliding Tribology of Powder‐Metallurgy Al7075 Composites Reinforced With Sol–Gel‐Derived ZnO–rGO Hybrid Nanoparticles

Advanced Engineering Materials, EarlyView.
Sol–gel‐derived ZnO–rGO hybrid nanoparticles enable Al7075 powder‐metallurgy composites to achieve concurrent gains in hardness and thermal conductivity while markedly lowering friction and wear. The hybrid architecture couples ZnO‐based load support with rGO‐assisted lamellar sliding and heat spreading, revealing a promising route toward lightweight ...
Bunyamin Aksakal, Cevher Kursat Macit, Merve Ayık, Hakan Tutumlu   +3 more
wiley   +1 more source

Active Corrosion Protection of Sintered AA7075 Aluminum Alloy via Mn Powder Addition

Advanced Engineering Materials, EarlyView.
AA7075 containing Mn‐rich particles is fabricated via spark plasma sintering using AA7075 and Mn powders. Corrosion resistance is evaluated through dip‐and‐dry tests using 0.1 M NaCl (pH 6.0), and mass loss decreases with increasing Mn addition. Mn‐rich particles function as a source of Mn ions, and formation of Mn‐accumulation films on Cu‐containing ...
Ko Ebina, Masashi Nishimoto, Izumi Muto
wiley   +1 more source

Composites of Shellac and Silver Nanowires as Flexible, Biobased, and Corrosion‐Resistant Transparent Conductive Electrodes

Advanced Functional Materials, EarlyView.
Shellac, a centuries‐old natural resin, is reimagined as a green material for flexible electronics. When combined with silver nanowires, shellac films deliver transparency, conductivity, and stability against humidity. These results position shellac as a sustainable alternative to synthetic polymers for transparent conductors in next‐generation ...
Rahaf Nafez Hussein, Tiago Carneiro Gomes, Eliza Ng, Simon Rondeau‐Gagné, Tricia Breen Carmichael   +4 more
wiley   +1 more source

Digitizing the Filtration Interface: A Smart, Modular Janus Wood Platform for Self‐Reporting Oil/Water Remediation

Advanced Functional Materials, EarlyView.
This work developed a smart Janus wood membrane integrating asymmetric wettability with built‐in electrical sensing for oil‐water separation. The membrane achieved > 99.5% separation efficiency and high flux by leveraging wood's natural anisotropic pore structure.
Kaiwen Chen, Cheng Hao, Wenjuan Zhao, Haonan Zhang, Yujing Tan, Fengze Sun, Xuewen Han, Hui Peng, Tianyi Zhan, Jianxiong Lyu, Ning Yan   +10 more
wiley   +1 more source

Surprising Water Slipping Performance on Highly Hydrophilic PEG‐Derived Monolayer‐Covered Surfaces: Preparation, Mechanism, and Application

Advanced Functional Materials, EarlyView.
Highly hydrophilic surfaces (water contact angle, ≈17.7°) exhibiting surprising water slipping performance (sliding angle, ≈7.3°) are successfully prepared via simple chemisorption of polyethylene glycol (PEG) organosilane and subsequent alkali‐treatment.
Hyeonjin Kim, Kouki Akaike, Jerred Wassgren, Hiroshi Kakiuchida, Masahisa Okada, Atsushi Hozumi   +5 more
wiley   +1 more source