Forward modelling on GPR responses of subsurface air voids
, 2020 Xianghuan Luo +2 more
openalex +2 more sources
An image analysis procedure to quantify the air void system of mortar and concrete [PDF]
, 2014 P.C. Fonseca, George W. Scherer
openalex +1 more source
Surface Tension Measurement of Ti‐6Al‐4V by Falling Droplet Method in Oxygen‐Free Atmosphere
Advanced Engineering Materials, EarlyView.In this article, the temperature‐dependent surface tension of free falling, oscillating Ti‐6Al‐4V droplets is investigated in both argon and monosilane doped, oxygen‐free atmosphere. Droplet temperature and oscillation are captured with one single high‐speed camera, and the surface tension is calculated with Rayleigh's formula.
Johannes May +9 more
wiley +1 more source
The Post–endodontic Adhesive Interface: Theoretical Perspectives and Potential Flaws [PDF]
, 2018 Introduction The aim of this review was to analyze the potential of successful bonds of endodontic posts to radicular dentin as well as the limitations of the post–endodontic adhesive interface. Methods The MEDLINE/PubMed and Web of Science electronic
He, Jianing +2 more
core +1 more source
Numerical Modeling of Tank Cars Carrying Hazardous Materials With and Without Composite Metal Foam
Advanced Engineering Materials, EarlyView.Large‐scale puncture models consisting of hazardous materials (HAZMATs) tank car with protective steel–steel composite metal foam (S–S CMF) are solved numerically. Tank car plate with added 10.91–13.33 mm thick S–S CMF layer does not puncture. Protective S–S CMF absorbs impact energy, reduces plate deformation, and prevents shear bands formation ...
Aman Kaushik, Afsaneh Rabiei
wiley +1 more source
Dielectric-Based Estimation of HMA Dynamic Modulus
Construction MaterialsThis research aims to investigate the possibility of measuring dielectric constant as an alternative proxy for estimating E* through a non-destructive procedure.
Konstantina Georgouli, Andreas Loizos
doaj +1 more source
Advanced Engineering Materials, EarlyView.This study investigates the effects of milling parameters, including rotational speed, milling duration, and ball‐to‐powder ratio, on TiAl particle size and morphology in an XHV‐equivalent atmosphere. The creation of oxide‐free surfaces enhances the mechanical properties of green bodies.
Jytte Möckelmann +4 more
wiley +1 more source
Implementation of High Air Voids Asphalt Mixtures on Trial Section—Performance Evaluation Case Study
Applied SciencesAsphalt mixtures designed with an elevated air void content are intended to lower traffic noise as well as to improve traffic safety and quality by improving rainwater evacuation through the layer of the surface mixture, not just on top of it.
Wojciech Bańkowski +3 more
doaj +1 more source
Microstructure Design of Steel‐Spinel Composites via Spark Plasma Sintering Process
Advanced Engineering Materials, EarlyView.This study illustrates how spark plasma sintering at reduced oxygen partial pressure enables controlled formation of steel‐spinel composites through tailored redox reactions and cation exchange. Comparison of the MgO–Fe2O3, steel–(MgO+Cr2O3), and steel–(MgO+Fe2O3) systems shows how oxygen activity and interface chemistry govern spinel formation, phase ...
Mahnaz Mehdizadehlima +4 more
wiley +1 more source
Microstructure Evolution of a VMnFeCoNi High‐Entropy Alloy After Synthesis, Swaging, and Annealing
Advanced Engineering Materials, EarlyView.The synthesis and processing (rotary swaging and annealing) of the novel VMnFeCoNi alloy is investigated, alongside the estimation of the grain size effect on hardness. Analysis of a wide grain size range of recrystallized microstructures (12–210 µm) reveals a low annealing twin density.
Aditya Srinivasan Tirunilai +6 more
wiley +1 more source