Results 31 to 40 of about 5,361 (218)
Aeroservoelastic analysis method for mixed-command fault of flight control system
Hangkong gongcheng jinzhanLarge civil aircraft fly-by-wire flight control systems may experience a fault condition where both normal mode and direct mode control commands are output simultaneously. It is necessary to propose a method to demonstrate the airworthiness compliance of
DING Luning, YANG Fei, LI Peng
doaj +1 more source
Current Status and Challenges in Data Collection for Aerospace Coatings Deposited by Plasma Spraying
Advanced Engineering Materials, EarlyView.An innovative approach has been integrated into the GRENAT project to optimize plasma spraying and coating performance. Raw materials are accelerated and melted in the plasma generated by torches, creating coatings. Monitoring sensors collect process data which are combined with ex situ characterization data.
Lila Randriamananjara +8 more
wiley +1 more source
Advanced Engineering Materials, EarlyView.Scandium (Sc)‐doped AlCoCrFeMo HEA coatings are fabricated via flame spraying with 0.1, 0.3, and 0.5 wt% Sc additions. Among these, the HEA‐Sc0.3 coating exhibits the highest corrosion resistance, indicated by a more positive corrosion potential and lower current density.
Pankaj Kumar +7 more
wiley +1 more source
Design and verification of skylight environment simulation system for civil aircraft
Hangkong gongcheng jinzhanThe external light environment has high impact on pilot comfort and aircraft control safety, which can affect the design of the cockpit light environment.
GUO Weihong +4 more
doaj +1 more source
Present Status and Prospect of Ultra High Strength Steel Applied to Aircraft Landing Gear
Journal of Aeronautical Materials, 2017 The paper presents the domestic and overseas current status of the steel applied to aircraft landing gear in combination of the design concept and requirements for aircraft landing gear.
ZHAO Bo, XU Guangxing, HE Fei, YANG Xu
doaj +1 more source
Xibei Gongye Daxue Xuebao, 2023 A combination of numerical simulation and experimental test is carried out, and the vortex core visualization technology is adopted to visualize vortex in the flow field and study the heat transfer mechanism. The heat transfer characteristics of air flow
LI Haofan, YUN Xue
doaj +1 more source
Advanced Engineering Materials, EarlyView.This study shows that superalloys used in aircraft engine disks become much more prone to deformation at high temperatures if they have been strained during manufacturing. This effect increases with the level of prior strain but eventually reaches a limit.
Fabio Machado Alves da Fonseca +9 more
wiley +1 more source
Advanced Engineering Materials, EarlyView.Sol–gel‐derived ZnO–rGO hybrid nanoparticles enable Al7075 powder‐metallurgy composites to achieve concurrent gains in hardness and thermal conductivity while markedly lowering friction and wear. The hybrid architecture couples ZnO‐based load support with rGO‐assisted lamellar sliding and heat spreading, revealing a promising route toward lightweight ...
Bunyamin Aksakal +3 more
wiley +1 more source
Advanced Engineering Materials, EarlyView.This review comprehensively evaluates extrusion‐based additive manufacturing for advanced ceramics, detailing feedstock options and key process parameters. By critically addressing defect mechanisms like porosity and cracking, the work highlights optimization strategies through machine learning and advanced postprocessing.
Meisam Bakhtiari +4 more
wiley +1 more source
Advanced Functional Materials, EarlyView.A multifunctional structural power composite is developed by integrating high‐mass‐loading Zn‐ion hybrid supercapacitors with metal mesh current collectors and aramid nanofiber‐based composite electrolytes, enabling simultaneous load‐bearing capability and enhanced areal energy storage.
Yuseung Choi +8 more
wiley +1 more source