Results 11 to 20 of about 9,395 (197)

Experimental Study of Mechanical Properties of AISI 1045, AISI 1053 and AISI 4140 Steels

International Journal of Engineering and Advanced Technology, 2020
AISI 1045, AISI 1053 and AISI 4140 are the mostly used material for axle shaft of a vehicle. The comparative study of these materials definitely will help in selection of appropriate material for required condition. AISI 4140 has shown greater Young’s modulus, yield strength and tensile strength, but moderate ductility is observed. The lesser ductility
Rajesh P Verma, Durgeshwar Singh, Shwetank Avikal   +2 more
openaire   +1 more source

Mechanical Properties of Boronized AISI 316, AISI 1040, AISI 1045 and AISI 4140 Steels

Acta Physica Polonica A, 2009
In this study, some mechanical properties of borided and unborided four steels were investigated. Boronizing of steels was performed by powder pack method at 1210 K for 4 h. The hardness of borides, boride layer thickness and room temperature tensile properties were measured and it was observed that hardness and tensile properties strongly depend on ...
Sahin, O., UÇAR, Nazım, Çalık, ADNAN
openaire   +3 more sources

Comparative Study of Conventional and Microwave-Assisted Boriding of AISI 1040 and AISI 4140 Steels

Tehnički Glasnik, 2023
In this study, AISI 1040 and AISI 4140 steels were boriding using Ekabor-II commercial boriding powder with powder-pack boriding method using microwave and conventional heating methods.
Safiye İpek Ayvaz, Emre Özer
doaj   +1 more source

Investigation of Pitting Corrosion Rate on Micro Plasma Arc Welded Dissimilar Weld Joints of AISI 304 and AISI 430 Stainless Steel Sheets [PDF]

International Journal of Advanced Design and Manufacturing Technology, 2020
In the present paper investigation is carried out to study pitting corrosion rate of Pulsed Current Micro Plasma Arc welded AISI304 and AISI430 dissimilar joint in three different mediums namely 0.5N NaOH, 3.5N NaCl and 0.5N HCl.
Uma Maheswara Rao G, Srinivasa Rao Chalamalasetti   +1 more
doaj   +1 more source

Microstructure and Wear Behavior of TiC/AISI 1020 Metal Matrix Composites Produced by Liquid Pressing Infiltration

Applied Sciences, 2021
A metal matrix composite was developed through a unique liquid pressing infiltration process to study the wear mechanism of a TiC reinforced AISI 1020 steel matrix.
Heejeong Kim, Jungyu Park, Sangmin Shin, Seungchan Cho, Junghwan Kim, Dong-Su Bae, Ilguk Jo   +6 more
doaj   +1 more source

Indices of systemic inflammation for predicting early infections after major joint arthroplasty

Travmatologiâ i Ortopediâ Rossii
Background. Infectious complications after arthroplasty pose a serious problem for both the patient and the health facility. Therefore, their prognosis is of great clinical importance.
Lyudmila V. Lyubimova, Evgeniya A. Mikishanina, Nikolay S. Nikolaev, Evgeniy A. Lyubimov, Elena V. Preobrazhenskaya   +4 more
doaj   +1 more source

Investigating the Effect of Cutting Condition on the Plastic Energy in Turning Process of AISI 1050 [PDF]

International Journal of Advanced Design and Manufacturing Technology, 2019
Reducing energy consumption is a demanding issue considering the limited available energy resources and increasing environmental pollution. On the other hand, industry consumes a huge amount of energy, and manufacturing processes are the most energy ...
Mohammad Meghdad Fallah, Seyyed Reza Hamzeloo   +1 more
doaj  

The Investigation Of Mechanical Properties And Welding With Flash Butt Welding Of AISI 1050, 304 And 430 Types Steels

Gazi Üniversitesi Fen Bilimleri Dergisi, 2019
In this study, AISI 304, AISI 430 stainless steel AISI type 1050 steel butt welding has been applied and its effects on the microstructure and mechanical properties of these materials were investigated application. The combined stiffness of the specimen,
Uğur ARABACI, Muhanmet Yaşar ÇİMEN
doaj   +1 more source

Morphology, Transport, and Dynamics of Protein Adsorption in Open‐Cell Metal Foam

Advanced Engineering Materials, EarlyView.
Stainless steel (SS) open‐cell foams are shown to adsorb more protein per unit area than previously reported 316L SS and chromium oxide surfaces under static and flow conditions. An integrated approach combining 3D pore imaging, flow simulation, and protein adsorption experiments characterizes the foam’s performance.
Chinmaya Prerana Inguva, Joseph Lavoie, Afsaneh Rabiei   +2 more
wiley   +1 more source

Effects of Mg on Microstructure and Solidification of a Hypereutectic Zn–8 wt.%Al Alloy

Advanced Engineering Materials, EarlyView.
An appreciable set of results involving thermal data, microstructure, chemical composition, and microstructural growth laws is reported for ZnAlMg alloys. Such results demonstrate that ZnAlMg alloys have high potential for applications in automotive self‐lubricating components, batteries, and electrical systems.
Raí B. de Sousa, Jeverton L. Paixão, Daylla S. Silva, Bruno S. Sobral, Mucio D. de Medeiros, José E. Spinelli, Bismarck L. Silva   +6 more
wiley   +1 more source