Results 61 to 70 of about 30,978 (228)

Effect of Cell Disruption and Protein Extraction on the Structural and Technological Properties of Tetradesmus obliquus Protein‐Rich Extracts

Sustainable Food Proteins, Volume 4, Issue 2, June 2026.
Despite its considerable potential as a functional food ingredient, T. obliquus faces a major limitation in protein recovery due to the rigidity of its cell wall. In the microalgae industry, protein extraction typically involves two main steps: cell disruption and protein extraction.
César Augusto Sodré da Silva, Tamires Souza Silva, Nayara Flores Fonseca, Rejane de Castro Santana, Jose Roberto Miranda Júnior, Márcio Arêdes Martins, Jane Sélia dos Reis Coimbra   +6 more
wiley   +1 more source

Functionalizing Conductive Diamond: Recent Advance in Fabrication, Modifications, and Applications

Carbon Energy, Volume 8, Issue 5, May 2026.
This review highlights recent advancements in the synthesis, modification, and electrochemical applications of conductive diamond, particularly boron‐doped diamond (BDD). It emphasizes progress in fabrication methods, including CVD and HPHT, and explores modifications such as doping, surface terminations, and composite design, enabling significant ...
Ning Linghu, Xin Jiang, Jing Xu
wiley   +1 more source

Review of Electrochemical Methods for Battery Recycling

Chemie Ingenieur Technik, Volume 98, Issue 5, Page 191-211, May 2026.
Electrochemical methods for the recycling of batteries are reviewed and different approaches for enhanced leaching, separation, and recovery methods are compared regarding their efficiency and suitability for potential application. ABSTRACT Research on innovative methods for the recycling of battery waste materials using electrochemical procedures is ...
Christian Modrzynski
wiley   +1 more source

Characterization of Laser Structuring on AISI 304 Stainless Steel

Al-Nahrain Journal for Engineering Sciences
Super-hydrophobic is the tendency of a surface to spit out water droplets. Only a surface with high apparent contact angle (>1500), low contact angle hysteresis (<100), low sliding angle (<50), and strong Cassie model state stability is considered a super-hydrophobic surface.
Sarah Sabah Edan, Rana M. Taha
openaire   +2 more sources

Duplex Stainless Steel Laser‐Surface Textured: Stability in Brine Solution

Advanced Engineering Materials, Volume 28, Issue 8, 22 April 2026.
Controlled laser‐surface treatment (LST) of duplex DSS2205 steel is performed to increase its stability in brine solution under cyclic electrochemical assays. The superior protection with respect to flat and smooth panels is attributed to the presence of FeCr2O4 as the main protective oxide layer in the LST surface, after corrosion tests. The stability
Mohammad Rezayat, Hamidreza Enshaei, Elaine Armelin, José I. Iribarren, Antonio Mateo, Miguel Morales   +5 more
wiley   +1 more source

Comparison of the thermoelastic phenomenon expressions in stainless steels during cyclic loading

Metalurgija, 2017
The main purpose of this paper is to compare the thermoelastic stress in specimens of stainless steel. As material specimens we chose stainless steel of AISI 304, AISI 316Ti and AISI 316L types.
M. Sapieta, A. Sapietova, V. Dekys
doaj  

Dynamic Study of Current Fluctuations of Nanostructured Films

International Journal of Electrochemical Science, 2012
The objective of the current research work is to study the polarization curves and electrochemical noise, the performance and nonlinear dynamic of corrosion protection of a nanostructured thin film of AISI 304 stainless steel on a AISI 304 substrate ...
C. López-Meléndez, E.M. Garcia-Ochoa, M.I. Flores-Zamora, R.G. Bautista-Margulis, C. Carreño-Gallardo, C.P. Castillo Morquecho, J.G. Chacon-Nava, A. Martínez-Villafañe   +7 more
doaj   +1 more source

Effect of PWHT and Electrical Parameters on Austenitic Phase, Sigma Phase and Corrosion in Duplex Steels S32205

Engineering Reports, Volume 8, Issue 4, April 2026.
Welding power and post‐weld heat treatment (PWHT) at 850°C influence phase transformations in S32205 duplex stainless steel, promoting sigma phase formation and reducing corrosion resistance. PWHT at 850°C also replicates HAZ‐like microstructures in base metal, enabling improved characterization of weld joint properties.
Sandra Chacón‐Fernández, José L. Meseguer‐Valdenebro, Andrea Peña Martín   +2 more
wiley   +1 more source

Hardness, grainsize and porosity formation prediction on the Laser Metal Deposition of AISI 304 stainless steel

International journal of machine tools & manufacture, 2018
The presented numerical model solves the heat and mass transfer equations in the Laser Metal Deposition process and based on the evolution of the thermal field predicts the grainsize, the resulting hardness and evaluates the pores formation probability ...
J. I. Arrizubieta, A. Lamikiz, Magdalena Cortina, E. Ukar, A. Alberdi   +4 more
semanticscholar   +1 more source

Friction welding of 304 austenitic stainless steel tube to tube plate joints using an external tool

Journal of Advanced Mechanical Design, Systems, and Manufacturing, 2015
The present study has been focused on friction welding of AISI 304 austenitic stainless steel tube to tube plate joints using an external tool. Friction welding of tube to tube plate using an external tool (FWTPET) is invented in the year 2006.
Subbanchetty PANDIA RAJAN, Selvaraj SENTHIL KUMARAN, Lakshmi annamalai KUMARASWAMIDHAS   +2 more
doaj   +1 more source