Results 111 to 120 of about 2,308 (222)

MECHANICAL BEHAVIOR OF AISI 316 STAINLESS STEEL SHEETS AT VARYING DEFORMATION TEMPERATURES AND STRESS STATES [PDF]

reservedLa presente tesi indaga il comportamento meccanico delle lamiere in acciaio inossidabile AISI 316 al variare della temperatura di deformazione e dello stato tensionale.
KALLAKU, ALBAN
core  

Caracteristicas da usinabilidade de aços inoxidaveis austeniticos SAE 304 e SAE 316 com a variação dos parametros metalurgicos [PDF]

, 1996
Dissertação (mestrado) - Universidade Federal de Santa Catarina, Centro TecnologicoEsta Dissertaçao apresenta uma série de informações a respeito de testes de torneamento longitudinal realizados com o objetivo de verificar as possíveis diferenças de ...
Gomes, Jefferson de Oliveira
core  

Ultrasonic fatigue testing of AISI 304 and 316 stainless steels under environmental and immersion conditions

Fracture and Structural Integrity
Ultrasonic fatigue tests were carried out on stainless steel AISI 316 and 304, under two modalities: at room temperature and in immersion (water for 316 and antifreeze for 304 steels); all tests were carried out with a loading ratio R=-1.
Luis M. Torres Duarte, Gonzalo M. Dom�nguez Almaraz, Hip�lito M. Venegas Monta�o   +2 more
doaj   +1 more source

Evaluation of Heat-Treated AISI 316 Stainless Steel in Solar Furnaces to Be Used as Possible Implant Material. [PDF]

Materials (Basel), 2020
Milosan I, Florescu M, Cristea D, Voiculescu I, Pop MA, Cañadas I, Rodriguez J, Bogatu CA, Bedo T.   +8 more
europepmc   +1 more source

Experimental and theoretical investigations of benzoic acid derivatives as corrosion inhibitors for AISI 316 stainless steel in hydrochloric acid medium: DFT and Monte Carlo simulations on the Fe (110) surface. [PDF]

RSC Adv, 2020
Alahiane M, Oukhrib R, Albrimi YA, Oualid HA, Bourzi H, Akbour RA, Assabbane A, Nahlé A, Hamdani M.   +8 more
europepmc   +1 more source

Development and Examination of Coated Coronary Stents [PDF]

, 2007
The aim of this study is to show the developments carried out by us with coated stents, expansion properties, furthermore the failures of the coatings. The coating was examined before and after expansion, paying special attention to the curves.
Dobránszky, János, Bognár, Eszter, Ring, György, Marton, Hilda Zsanett   +3 more
core  

Surface modification of AISI 316 L stainless steel with polyvinyl alcohol/chitosan/sol-gel bioactive glass coating by electrospinning method

Applied Surface Science Advances
AISI 316 L stainless steel has several applications in biomedical implants owing to its good corrosion resistance and mechanical properties. However, 316 L stainless steel alone may not provide sufficient biocompatibility.
Masoud Rezaei, Sayed Mahmood Rabiee, Rohollah Jamaati, Shahrzad Rahmani   +3 more
doaj   +1 more source

A sulfidation- and oxidation-resistant ferritic stainless steel containing aluminum [PDF]

"The Bureau of Mines is conducting research on substitute materials having greater resistance to high-temperature corrosive atmospheres above 600 deg. C compared to austenitic stainless steels such as aisi 304, 316, and 310, with the goal of conserving ...

core  

Sigma Phase Characterization in AISI 316 Stainless Steel [PDF]

Microscopy and Microanalysis, 2005
openaire   +1 more source

DISTRIBUSI GAYA PADA PEMOTONGAN STAINLESS STEEL AISI 316 AKIBAT VARIASI SUDUT TATAL MENGGUNAKAN PAHAT HSS [PDF]

, 2014
Proses bubut merupakan proses permesinan yang sering digunakan untuk membuat atau memproses benda-benda berbentuk silindris, dalam komponen mesin karakteristik hasil bubut sangat dipertimbangkan.
Yogga Catur Candra
core