Results 151 to 160 of about 809,589 (339)

Current Tracking Adaptive Control of Brushless DC Motors

International Journal of Adaptive Control and Signal Processing, EarlyView.
In this paper, the current tracking for Brushless Direct Current motors is approached considering uncertainty in the parameters of the motor's model. An adaptive control scheme to compensate electrical parameters uncertainty is proposed without requiring any knowledge of the mechanical parameters.
Fernanda Ramos‐García, Axel Coronado‐Andrade, Gerardo Espinosa‐Pérez, Luis Alvarez‐Icaza   +3 more
wiley   +1 more source

Effect of in-situ SiC particles on the room–temperature dry sliding wear behavior of Al–12Si–4Cu–2Ni–1Mg alloys

Journal of Materials Research and Technology
In-situ SiC particles (SiCip) show significant potential to elevate the wear behavior of Al matrix composites due to the improved SiC/Al interfacial bonding.
Chongchong Wu, Mengdi Zhang, Jing Zhou, Jingjing Ruan, Xiangfa Liu   +4 more
doaj   +1 more source

Mechanochemical Synthesis and Characterization of Nanostructured ErB4 and NdB4 Rare‐Earth Tetraborides

Advanced Engineering Materials, Volume 27, Issue 6, March 2025.
ErB4 and NdB4 nanostructured powders are produced by mechanochemical synthesis. 5 h mechanical alloying and 4 M HCl acid leaching are used in the production. ErB4 and NdB4 powders exhibit maximum magnetization of 0.4726 emu g−1 accompanied with an antiferromagnetic‐to‐paramagnetic phase transition at about TN = 18 K and 0.132 emu g−1 with a maximum at ...
Burçak Boztemur, Faruk Kaya, Bora Derin, Mustafa Lütfi Öveçoğlu, Ju Li, Duygu Ağaoğulları   +5 more
wiley   +1 more source

Enhancing Corrosion Resistance and Mechanical Strength of 3D‐Printed Iron Polylactic Acid for Marine Applications via Laser Surface Texturing

Advanced Engineering Materials, EarlyView.
Laser surface texturing significantly improves the corrosion resistance and mechanical strength of 3D‐printed iron polylactic acid (Ir‐PLA) for marine applications. Optimal laser parameters reduce corrosion by 80% and enhance tensile strength by 25% and ductility by 15%.
Mohammad Rezayat, Mojtaba Karamimoghadam, Mohammadreza Lalegani Dezaki, Ali Zolfagharian, Giuseppe Casalino, Antonio Mateo, Mahdi Bodaghi   +6 more
wiley   +1 more source

Understanding the Effect of Resistance Temperature Detector Temperature Controllers on Microstructural Alignment in Magnetic Freeze Casting

Advanced Engineering Materials, EarlyView.
The effect of temperature controllers that are commonly used in freeze‐casting is investigated in this work. Temperature controllers are observed to generate a voltage in the slurry. Microstructural alignment and ultimate compressive strength data show this voltage to interfere with the ability to align the microstructure using magnetic fields ...
Maddie A. Schmitz, Steven E. Naleway
wiley   +1 more source

Composite Electrospun Fibers Containing Optimized B‐ and Cu‐Doped Bioactive Glass Sol‐Gel Particles for Potential Soft Tissue Engineering Applications

Advanced Engineering Materials, EarlyView.
This article describes the preparation and characterization of poly(ε‐caprolactone) electrospun composite fibers incorporating sol‐gel‐derived bioactive glass particles doped with B and Cu. Scanning electron microscopy, energy‐dispersive X‐ray spectroscopy, Fourier‐transform infrared spectroscopy, contact angle, acellular bioactivity, mechanical and ...
Elisa Piatti, Marta Miola, Liliana Liverani, Paolo Sartori, Enrica Verné, Aldo R. Boccaccini   +5 more
wiley   +1 more source

Unlocking the Power of Quercetin‐Encapsulated Mesoporous Bioactive Glass Nanoparticles: A Multifunctional Approach to Bone Regeneration

Advanced Engineering Materials, EarlyView.
Mesoporous bioactive glass nanoparticles (MBGNs) are investigated for bone regeneration given their remarkable structural and functional properties. MBGNs are functionalized with Mn and Cu and incorporated with quercetin, a natural flavonoid exhibiting antioxidant, anti‐inflammatory, and antimicrobial properties.
Giovanni Lo Bello, Qaisar Nawaz, Pier Francesco Ferrari, Laura Pastorino, Roberto Raiteri, Aldo R. Boccaccini   +5 more
wiley   +1 more source

Adjustment of Coatings Morphology and Particle Distribution of Layered Silicates by Freeze‐Drying for Improved Gas Barriers

Advanced Engineering Materials, EarlyView.
Freeze‐drying of layered silicate is the key to get coatings with superior gas barrier. Freeze‐drying of layered silicates modified with dodecylamine (DDA) is a highly effective technique for the preparation of barrier pigments that significantly mitigate the permeation of oxygen, water vapor, and hydrogen through polymer films containing these ...
Joshua Lommes, Moritz Bätcher, Andrea Deißenberger, Volkmar Stenzel, Andreas Hartwig   +4 more
wiley   +1 more source

On the Impact Energy Absorption of an Advanced High‐Strength Bilayer Steel Composite Consisting of Carbide‐Free Bainitic Steel and High‐Mn Twinning‐Induced Plasticity Steel

Advanced Engineering Materials, EarlyView.
Excellent combinations of strength and impact toughness are obtained in a bilayer composite of high‐strength carbide‐free bainitic (CFB) steel and high‐ductility twinning‐induced plasticity (TWIP) steel. The composite absorbs energy at small strains when the notch is placed on the TWIP side and at high strains when the notch is placed on the CFB side ...
Kendra Hawke, Xiaogang Li, Amir Partovi, Colin Scott, Fateh Fazeli, Hatem Zurob   +5 more
wiley   +1 more source

Is Young's Modulus a Critical Coating Property Determining Fouling‐Release Performance of Marine Coatings?

Advanced Engineering Materials, EarlyView.
The release of foulers from protective marine coatings is determined by several interrelated material properties, including the strength of Young's modulus, the flexibility of chain segments, the surface free energy, and the magnitude of hydrodynamic stress.
Johann C. Schaal, Andreas Brinkmann, Andreas Hartwig   +2 more
wiley   +1 more source