Results 271 to 280 of about 423,347 (319)
Some of the next articles are maybe not open access.
Aluminium Alloys by Mechanical Alloying
Aircraft Engineering and Aerospace Technology, 1987After years of research, an important development in powder metallurgy is about to enter commercial production with the commissioning by Inco Alloys International of its $4 million plant in Pittsboro, North Carolina, to produce aluminium and other light metal alloys by mechanical alloying.
openaire +1 more source
Calcium-alloyed magnesium alloys
Metal Science and Heat Treatment, 2009Mg - Al - Ca alloys positioned in the Mg - Al 2 Ca quasi-binary section are studied. It is shown that alloys of this system bearing the Al 2 Ca compound as a hardening phase can be used for developing structural alloys with elevated strength at 170°C and that the strength characteristics of the Mg - Al - Ca alloys can be improved by adding manganese.
L. L. Rokhlin +3 more
openaire +1 more source
Mechanical Alloying of Aluminium Alloys
Mechanical alloying is a solid-state powder processing technique that has revolutionized the development of advanced materials, including aluminium alloys. This chapter provides a concise overview of the key aspects of mechanical alloying applied to aluminium alloys, exploring its principles, advantages, and potential applications.Rayappa Shrinivas Mahale +8 more
openaire +1 more source
Complex alloying of titanium alloys
Metal Science and Heat Treatment, 19751. The effectiveness of complex alloying was established, in which the strength of both the α and β solid solutions increases, and the difference between their strengths decreases. This leads to more even plastic deformation and more complete utilization of the strength of the α and β phases. 2.
openaire +1 more source
Alloying Aluminum Alloys with Scandium
Metal Science and Heat Treatment, 2017Methods and procedures are discussed for more economic and effective use of scandium for alloying aluminum alloys. Specifically, it is recommended to introduce scandium and zirconium into aluminum alloys in a 1 : 1 ratio instead of the usual 3 : 1 with the same overall element content.
V. V. Zakharov, I. A. Fisenko
openaire +1 more source
Heat-Resistant RuAl-Based Alloys: III. Powder Alloys—Mechanical Alloying
Inorganic Materials: Applied Research, 2021Refractory (Tmelt = 2100 °C), heat-resistant ruthenium monoaluminide RuAl, lighter (ρ = 7.97 g/cm3) than Ni superalloys, is considered as a promising candidate material for operation at high temperatures and relatively low loads in high-speed gas oxidizing flows at temperatures higher not only operating temperatures, but also the melting temperatures ...
K. B. Povarova +4 more
openaire +1 more source
Properties of alloyed Ni?Be alloys
Metal Science and Heat Treatment, 19661. In Ni−Be spring alloys alloyed with Mo, Mo+B, W, and V the resistance to small plastic deformation increases. 2. The strengthening of Ni−Be alloys containing Mo, W, or V is due to the precipitation of a greater number of particles of the β'-phase because of the decrease in the solubility of Be in the nickel solid solution.
V. A. Borisov +2 more
openaire +1 more source
CUPRON ALLOY, PCLW-SNX ALLOY and PCLW-BPX ALLOY
Alloy Digest, 1992Abstract CUPRON Alloy is the standard negative thermoelement used with copper, with iron and with TOPHEL Alloy in ISA Types T, J and E thermocouples, respectively. PCLW-SNX and PCLW-BPX are thermocouple extension wire alloys. This datasheet provides information on composition, physical properties, and tensile properties.
openaire +1 more source
A state-of-the-art review on fatigue performance of powder bed fusion-built alloy 718
Progress in Materials Science, 2023Filippo Berto +2 more
exaly