Results 131 to 140 of about 64,636 (303)
Advanced Engineering Materials, EarlyView.This plot compares experimental tensile stress–strain curves (with 4 different strain rates) and corresponding modelled curves (obtained using the optimised sets of Voce and Miller–Norton parameter values shown). The inferred M‐N values, characterizing the creep, are very similar to those obtained via conventional creep testing.
S. Ooi, R. P. Thompson, T. W. Clyne
wiley +1 more source
Creep damage is a time-dependent deformation in metals under a constant stress at high temperature condition. Since the 1980s, high chromium alloy steel P91 (9%Cr-1%Mo-0.25%V) is highly demanded in high temperature industries (Saha, 2003).
An, Lili
core
Treatment Technology of EAF Dust at Stainless Steel Works
Teshugang, 2006 The EAF dust at stainless steel works mainly consists of ejected liquid drops of metal and slag formed by breaking of CO bubbles produced by alloy elements evaporation and decarburization reaction and small particles of charging exhausted with waste gas.
马国军, 倪红卫, 薛正良
doaj
Advanced Engineering Materials, EarlyView.Graphene nanoplatelet (0.1 wt.%) reinforcement significantly enhances the performance of β Ti‐28Nb‐35.4Zr alloy. Grain refinement, reduced water contact angle, and improved surface characteristics promote osteoblast adhesion and complete surface coverage after 7 days.
Khurram Munir +5 more
wiley +1 more source
Advanced Engineering Materials, EarlyView.Scandium (Sc)‐doped AlCoCrFeMo HEA coatings are fabricated via flame spraying with 0.1, 0.3, and 0.5 wt% Sc additions. Among these, the HEA‐Sc0.3 coating exhibits the highest corrosion resistance, indicated by a more positive corrosion potential and lower current density.
Pankaj Kumar +7 more
wiley +1 more source
Cathodic Cage Plasma Deposition of Nanostructured Cu–Fe–Se Coatings on Poly(methyl Methacrylate)
Advanced Engineering Materials, EarlyView.Nanostructured Cu–Fe–Se coatings are deposited on PMMA by a modified cathodic cage plasma process, enabling low‐temperature deposition on polymer substrates. A transition from discontinuous to compact morphology is observed with temperature, with optimal properties at 200°C, where improved CuFeSe2‐type bonding, lowest sheet resistance, and favorable ...
V. S. S. Sobrinho +8 more
wiley +1 more source
AIP AdvancesIn this work, an AISI 4340 high-strength steel alloy was surface machined to have four different grades of roughness (Ra). The impact of changing Ra on the corrosion of the steel alloy in 3.5% NaCl solutions after 40 min and 24 h was performed using ...
El-Sayed M. Sherif +2 more
doaj +1 more source
Nondestructive Testing of Welded Composite Metal Foams
Advanced Engineering Materials, EarlyView.X‐ray computed tomography (CT) is used to evaluate welded steel–steel composite metal foam (CMF) joints of two density classes. It reports variation in postweld spatial void distribution and correlates it to weld‐induced changes, mechanical performance, and failure within welded CMF panels.
Chinmaya Prerana Inguva +2 more
wiley +1 more source
Advanced Engineering Materials, EarlyView.Aluminum and nitride coatings are used in industry because they are hard, resist wear, and protect against oxidation. Adding boron can improve friction behavior and other properties. This study tests coatings on surfaces with different finishes. Results show smoother surfaces perform better, while rough ones wear faster, although coatings can reduce ...
Adrián Claver +9 more
wiley +1 more source